- 您現在的位置：買賣IC網 > PDF目錄367918 > PG-FP4 PG-FP4 Flash Memory Programmer | User＇s Manual[03/2003] PDF資料下載
參數資料
| 型號： | PG-FP4 |
| 英文描述： | PG-FP4 Flash Memory Programmer | User＇s Manual[03/2003] |
| 中文描述： | 指引FP4閃存編程|用戶手冊[03/2003] |
| 文件頁數： | 114/117頁 |
| 文件大?。?/td> | 1599K |
| 代理商： | PG-FP4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁當前第114頁第115頁第116頁第117頁
CHAPTER 10 ERROR MESSAGES
User’s Manual U15260EJ3V1UM
114
10.4 GUI Software Information Messages
Informational messages do not need any workaround because they do not indicate an error condition. The
message is sent as information only and does not require any user action in response.
No.
Message
Description
I 200
New firmware installed successfully in your
programmer!
Firmware upgrade completed with success.
I 201
Opening parallel download port failed.
File download will be done on the serial port.
The Windows internal function to open the parallel port
failed (port occupied by other software)
I 202
Download via parallel port failed.
Communication via the parallel port failed. Re-download or
use a serial port.
I 300
Value out of range.
The value entered in a dialog box is out of the allowable
max/min range. The max/min value or the most recent
value will be written into the dialog element.
I 301
Multiple Program Areas are disabled.
Please enable Program Areas usage in the Device
Setup Dialog.
The menu command [Programmer]
→
[Select
Programming area] can only be used when it has been
enabled on the Advanced tab of the device Setup dialog
box.
I 500
Operation completed successfully.
Executing a command succeeded.
I 501
This command can only be used for UC2 devices.
The menu entries Device
→
Write Security and Device
Checksum can only be used for UC2 devices.
I 502
Note:
To abort a write, erase or verify operation it is
necessary to reset the programmer manually.
Aborting device-related commands requires an additional
Programmer reset.
I 801
End record not found, created.
The HEX Editor implicitly created an end record when
loading a file.
I 800
Buffer is modified.
Are you sure to close
I 802
The file is modified.
Save
I 804
The file is modified.
Are you sure to quit
The HEX Editor indicates that its contents are not yet
saved to a disk.
I 805
This file is not valid.
The HEX Editor is attempting to open an invalid file.
I 905
*.set is not valid. Using most recent settings.
The SET file format is old.
I 906
*.prm is not valid. Using most recent settings.
The PRM file format is old.
I 907
Caution: When 'Chip Erase' is disabled, chip
cannot be erased and programmed any more!
This is displayed when [Disable Chip Erase] on Advanced
tab of the [Device]
→
[Setup] menu is checked.
I 911
The selection is out of range.
The value of [Speed] on the Standard tab of the [Device]
→
[Setup] menu exceeds the maximum value.
I 912
The selection is out of range.
The value of [Speed] on the Standard tab of the [Device]
→
[Setup] menu is smaller than the minimum value.
I 913
Value is out of range.
The value of [Frequency] on the Standard tab of the
[Device]
→
[Setup] menu exceeds the maximum value.
I 914
Value is out of range.
The value of [Frequency] on the Standard tab of the
[Device]
→
[Setup] menu is smaller than the minimum
value.
相關PDF資料 |
PDF描述 |
|---|---|
| PG1001 | TRANSISTOR | BJT | NPN | 60V V(BR)CEO | 2A I(C) | TO-46 |
| PG1002 | TRANSISTOR | BJT | NPN | 80V V(BR)CEO | 2A I(C) | TO-46 |
| PG1003 | TRANSISTOR | BJT | NPN | 100V V(BR)CEO | 2A I(C) | TO-46 |
| PG1004 | TRANSISTOR | BJT | NPN | 140V V(BR)CEO | 2A I(C) | TO-46 |
| PG1005 | TRANSISTOR | BJT | NPN | 160V V(BR)CEO | 2A I(C) | TO-46 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PG-FP4-E | 功能描述:PROGRAMMER FLASH MEMORY UNIV RoHS:是 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:* 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
| PG-FP5 | 制造商:Renesas Electronics Corporation 功能描述:MCU,Programmer,NEC Flash MCU |
| PG-FP5-AS | 制造商:Renesas Electronics Corporation 功能描述:MICROCOMPUTER FLASH MEMORY PROGRAMMER 制造商:Renesas Electronics Corporation 功能描述:PROGRAMMER FLASH RL78 V850 7 |
| PG-FP5-EA | 功能描述:PROGRAMMER FLASH MEMORY UNIV RoHS:是 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:* 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
| PGFP-A11 | 功能描述:PLUG GFCI 120VAC 15/20A AUTORST RoHS:是 類別:過電壓，電流，溫度裝置 >> 接地故障電路斷路器 (GFCI) 系列:PGFP 標準包裝:1 系列:PGFI 類型:帶 6 英尺引線的直列接頭 技術規格:120V 其它名稱:723-1041 |
發布緊急采購，3分鐘左右您將得到回復。