參數資料
型號： PCM1851PJT
英文描述： 24-BIT, 96-kHz STEREO A/D CONVERTER WITH 6 X 2-CHANNEL MUX AND PGA
中文描述： 24位，96千赫立體聲A / D轉換器6 × 2通道的MUX和PGA
文件頁數： 28/30頁
文件大小： 370K
代理商： PCM1851PJT
PCM1850
PCM1851
SLES108
MARCH 2004
www.ti.com
28
BOARD DESIGN AND LAYOUT CONSIDERATIONS
V
CC
, V
DD
Pins
The digital and analog power supply lines to the PCM1850/1851 must be bypassed to the corresponding ground pins with
0.1-
μ
F ceramic and 10-
μ
F electrolytic capacitors as close to the pins as possible to maximize the dynamic performance
of the ADC.
AGND, DGND Pins
To maximize the dynamic performance of the PCM1850/1851, the analog and digital grounds are not connected internally.
These grounds must have low impedance to avoid digital noise feeding back into the analog ground. Therefore, they should
be connected directly to each other under the parts to reduce the potential of a noise problem.
V
IN
L[1:6], V
IN
R[1:6] Pins
A 0.33-
μ
F capacitor is recommended as the ac-coupling capacitor, which gives a 2.4- to 8.5-Hz cutoff frequency. If higher
full-scale input voltage is required, it can be adjusted by adding only one series resistor to each V
IN
xx pin, but a signal source
resistance less than 1 k
is recommended for these pins in order to keep accuracy of the gain control command and to
maintain crosstalk performance.
MOUTL, MOUTR Pins
An ac-coupled light load is recommended; a 2.2-
μ
F capacitor with a 10-k
load gives a 7.2-Hz cutoff frequency.
V
REF
1, V
REF
2, V
REF
S Pins
Between V
REF
1 and AGND, V
REF
2 and AGND, and V
REF
S and AGND, 0.1-
μ
F ceramic and 10-
μ
F electrolytic capacitors
are recommended to ensure low source impedance of the ADC references. These capacitors should be located as close
as possible to the V
REF
1, V
REF
2, and V
REF
S pins to reduce dynamic errors on the ADC references. The differential voltage
between V
REF
2 and AGND sets the analog input full-scale range.
BCK and LRCK Pins (in Master Mode), DOUT Pin
These pins have enough load driving capability. However, if the output line is long, locating a buffer near the PCM1850/1851
and minimizing load capacitance is recommended in order to minimize the digital-analog crosstalk and maximize the
dynamic performance of the ADC.
System Clock
Because the PCM1850/1851 operates based on a system clock, the quality of the system clock can influence dynamic
performance. Therefore, it is recommended to consider the system clock duty, jitter, and the time difference between the
system clock transition and the BCK or LRCK transition in slave mode.
相關PDF資料
PDF描述
PCM2702 16-Bit Stereo DIGITAL-TO-ANALOG CONVERTER with Interface
PCM2702E 16-Bit Stereo DIGITAL-TO-ANALOG CONVERTER with Interface
PCM3000 Stereo Audio CODEC 18-BITS, SERIAL INTERFACE TM
PCM3000E Stereo Audio CODEC 18-BITS, SERIAL INTERFACE TM
PCM3001 Stereo Audio CODEC 18-BITS, SERIAL INTERFACE TM
相關代理商/技術參數
參數描述
PCM1851PJTG4 功能描述:音頻模/數轉換器 IC 24-Bit Stereo ADC w/6x2 ch MUX & PGA RoHS:否 制造商:Wolfson Microelectronics 轉換速率: 分辨率: ADC 輸入端數量: 工作電源電壓: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: 封裝:
PCM1851PJTR 功能描述:音頻模/數轉換器 IC 24-Bit Stereo ADC w/6x2 ch MUX & PGA RoHS:否 制造商:Wolfson Microelectronics 轉換速率: 分辨率: ADC 輸入端數量: 工作電源電壓: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: 封裝:
PCM1851PJTRG4 功能描述:音頻模/數轉換器 IC 24-Bit Stereo ADC w/6x2 ch MUX & PGA RoHS:否 制造商:Wolfson Microelectronics 轉換速率: 分辨率: ADC 輸入端數量: 工作電源電壓: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: 封裝:
PCM-186 功能描述:電線鑒定 Pre-Printed WM Card, Vinyl Cloth, .22" W RoHS:否 制造商:TE Connectivity / Q-Cees 產品:Labels and Signs 類型: 材料:Vinyl 顏色:Blue 寬度:0.625 in 長度:1 in
PCM1860DBT 功能描述:ADC, Audio 24 bit 192k I2S 30-TSSOP 制造商:texas instruments 系列:- 包裝:管件 零件狀態:有效 類型:ADC，音頻 分辨率（位）:24 b 采樣率（每秒）:192k 數據接口:I2S 電壓源:模擬和數字 電壓 - 電源:3 V ~ 3.6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商器件封裝:30-TSSOP 標準包裝:60
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*