參數資料
型號： PCF8833
廠商： NXP Semiconductors N.V.
英文描述： STN RGB - 132 X 132 X 3 driver
中文描述： 超扭曲的RGB - 132 × 132 × 3驅動程序
文件頁數： 70/112頁
文件大小： 469K
代理商： PCF8833
2003 Feb 14
70
Philips Semiconductors
Objective specification
STN RGB - 132
×
132
×
3 driver
PCF8833
9
SERIAL INTERFACE
Communication with the microcontroller can also occur via
a clock-synchronized serial peripheral interface. The
selection of this interface is achieved with pin PS0; see
Section 7.1.1.
The serial interface is a 3-line bidirectional interface for
communication between the microcontroller and the LCD
driver chip. The 3 lines are chip enable (SCE), Serial
Clock (SCLK) and Serial Data (SD). The PCF8833 is
connected to the SD pin of the microcontroller by two pins
SDIN (data input) and SDOUT (data output) which are
connected together.
9.1
Write mode
The Write mode of the interface means that the
microcontroller writes commands and data to the
PCF8833. Each data packet contains a control bit D/C and
a transmission byte. If bit D/C is logic 0, the following byte
is interpreted as a command byte. The command set is
giveninTable 1.IfbitD/Cislogic 1,thefollowingbytesare
stored in the display data RAM or registers. After every
RAM data byte the address counter increments
automatically. Figure 42 shows the general format of the
Write mode and the definition of the transmission byte.
Any instruction can be sent in any order to the PCF8833;
the MSB is transmitted first. The serial interface is
initialized when SCE is HIGH. In this state, SCLK pulses
have no effect and no power is consumed by the serial
interface. A falling edge on pin SCE enables the serial
interface and indicates the start of data transmission.
Figure 42 shows the protocol of the Write mode:
When SCE is HIGH, SCLKs are ignored. The serial
interface is initialized during the HIGH time of SCE.
At the falling edge of SCE SCLK must be LOW (see
Fig.51)
SDIN is sampled at the rising edge of SCLK
D/C indicates, whether the byte is a command (D/C = 0)
or data (D/C = 1). It is sampled with the first rising SCLK
edge.
If SCE stays LOW after the last bit of a data/command
byte, the serial interface will receive the D/C bit of the
next byte at the next rising edge of SCLK (see Fig.43).
A reset pulse at pin RES interrupts the transmission.
The data being written into the RAM may be corrupted.
The registers are cleared. If SCE is LOW after the rising
edge of RES, the serial interface is ready to receive the
D/C bit of a data/command byte; see Figs 44 and 50.
handbook, full pagewidth
MGU958
TB
D7
D6
D5
D4
D3
D2
D1
D0
MSB
LSB
transmission byte (TB)
may be a command OR a data byte
D/C
TB
D/C
D/C
TB
D/C
Fig.42 Serial data stream, Write mode.
相關PDF資料
PDF描述
PCF88331 STN RGB - 132 X 132 X 3 driver
PCF88332DA STN RGB - 132 X 132 X 3 driver
PCF8833U STN RGB - 132 X 132 X 3 driver
PCF8881 132 x 132 RGB single chip TFT driver with DC-to-DC converter
PCI-ADC MULTIFUNKTIONSKARTE 44 KANAL PCI BUS
相關代理商/技術參數
參數描述
PCF88331 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver
PCF88332DA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver
PCF8833U 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver
PCF8833U/2DA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver
PCF8881 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:132 x 132 RGB single chip TFT driver with DC-to-DC converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*