- 您現在的位置：買賣IC網 > PDF目錄382382 > PCF8598C-2T02 (NXP Semiconductors N.V.) 1024 ⅴ 8-bit CMOS EEPROM with I2C-bus interface PDF資料下載
參數資料
| 型號： | PCF8598C-2T02 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | DRAM |
| 英文描述： | 1024 ⅴ 8-bit CMOS EEPROM with I2C-bus interface |
| 中文描述： | 1024ⅴ8位CMOS EEPROM，帶有I2C總線接口 |
| 文件頁數： | 18/21頁 |
| 文件大小： | 395K |
| 代理商： | PCF8598C-2T02 |
Philips Semiconductors
PCF8598C-2
1024
×
8-bit CMOS EEPROM with I
2
C-bus interface
Product data
Rev. 06 — 22 October 2004
18 of 21
9397 750 14219
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
15.4 Package related soldering information
[1]
For more detailed information on the BGA packages refer to the (LF)BGA Application Note
(AN01026); order a copy from your Philips Semiconductors sales office.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods
For SDIP packages, the longitudinal axis must be parallel to the transport direction of the
printed-circuit board.
Hot bar soldering or manual soldering is suitable for PMFP packages.
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must
on no account be processed through more than one soldering cycle or subjected to infrared reflow
soldering with peak temperature exceeding 217
°
C
±
10
°
C measured in the atmosphere of the reflow
oven. The package body peak temperature must be kept as low as possible.
These packages are not suitable for wave soldering. On versions with the heatsink on the bottom
side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with
the heatsink on the top side, the solder might be deposited on the heatsink surface.
If wave soldering is considered, then the package must be placed at a 45
°
angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it
is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
Table 10:
Mounting
Suitability of IC packages for wave, reflow and dipping soldering methods
Package
[1]
Soldering method
Wave
Through-hole
mount
SDIP, SIL
Through-hole-
surface mount
Surface mount
BGA, LBGA, LFBGA,
SQFP, SSOP-T
[5]
,
TFBGA, VFBGA
DHVQFN, HBCC, HBGA,
HLQFP, HSQFP, HSOP,
HTQFP, HTSSOP,
HVQFN, HVSON, SMS
PLCC
[7]
, SO, SOJ
LQFP, QFP, TQFP
SSOP, TSSOP, VSO,
VSSOP
Reflow
[2]
Dipping
suitable
DBS, DIP, HDIP, RDBS,
suitable
[3]
PMFP
[4]
not suitable
not
suitable
suitable
not suitable
not suitable
[6]
suitable
suitable
not recommended
[7][8]
not recommended
[9]
suitable
suitable
suitable
相關PDF資料 |
PDF描述 |
|---|---|
| PCF86C410T | 8-BIT MICROCONTROLLER |
| PCF86C610P | 8-BIT MICROCONTROLLER |
| PCF86C610T | 8-BIT MICROCONTROLLER |
| PCF87852 | Bluetooth baseband controller |
| PCF87852E | Bluetooth baseband controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8598E-2P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| PCF8598E-2T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| PCF8598P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| PCF8598T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| PCF85XXC-2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:256 to 1024 ⅴ 8-bit CMOS EEPROMs with I2C-bus interface |
發布緊急采購，3分鐘左右您將得到回復。