- 您現在的位置：買賣IC網 > PDF目錄382381 > PCF2103EU (NXP Semiconductors N.V.) LCD controllers/drivers PDF資料下載
參數資料
| 型號： | PCF2103EU |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | LCD controllers/drivers |
| 中文描述： | LCD控制器/驅動器 |
| 文件頁數： | 17/56頁 |
| 文件大小： | 300K |
| 代理商： | PCF2103EU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
1998 May 11
17
Philips Semiconductors
Product specification
LCD controllers/drivers
PCF2103 family
8
INSTRUCTIONS
Only two PCF2103 registers, the Instruction Register (IR)
and the Data Register (DR) can be directly controlled by
the microcontroller. Before internal operation, control
information is stored temporarily in these registers to allow
interface to various types of microcontrollers which
operate at different speeds or to allow interface to
peripheral control ICs. The format for instructions when
I
2
C-bus control is used is shown in Table 6. The PCF2103
operation is controlled by the instructions given in Table 7
together with their execution time. Details are explained in
subsequent sections.
Instructions are of 4 types, those that:
1.
Designate PCF2103 functions such as display format,
data length, etc.
2.
Set internal RAM addresses
3.
Perform data transfer with internal RAM
4.
Others.
In normal use, instructions that perform data transfer with
internal RAM are used most frequently. However,
automatic incrementing by 1 (or decrementing by 1) of
internal RAM addresses after each data write lessens the
microcontroller program load. The display shift in particular
can be performed concurrently with display data write,
enabling the designer to develop systems in minimum time
with maximum programming efficiency.
During internal operation, no instruction other than the
‘read busy flag and address counter’ instruction will be
executed. Because the busy flag is set to logic 1 while an
instruction is being executed, the user should verify that
the busy flag is at logic 0 before sending the next
instruction or wait for the maximum instruction execution
time, as given in Table 7. An instruction sent while the
busy flag is logic 1 will not be executed.
Table 6
Instruction set for I
2
C-bus commands
Note
1.
R/W is set together with the slave address.
CONTROL BYTE
COMMAND BYTE
I
2
C-BUS COMMANDS
Co
RS
0
0
0
0
0
0
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 note 1
相關PDF資料 |
PDF描述 |
|---|---|
| PCF2104L | LCD controller/driver |
| PCF2104LU | LCD controller/driver |
| PCF2104N | LCD controller/driver |
| PCF2104NU | LCD controller/driver |
| PCF2105 | LCD controller/driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF2103EU/2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver |
| PCF2103EU/2/F2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
| PCF2103EU/F2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver |
| PCF2103FAMILY | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver |
| PCF2104C | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controller/driver |
發布緊急采購，3分鐘左右您將得到回復。