- 您現在的位置：買賣IC網 > PDF目錄382380 > PCD3359A (NXP Semiconductors N.V.) 8-bit microcontroller with DTMF generator and 128 bytes EEPROM PDF資料下載
參數資料
| 型號： | PCD3359A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| 中文描述： | 8位的DTMF產生器和128字節EEPROM的微控制器 |
| 文件頁數： | 17/32頁 |
| 文件大小： | 165K |
| 代理商： | PCD3359A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
1998 May 11
17
Philips Semiconductors
Product specification
8-bit microcontroller with DTMF
generator and 128 bytes EEPROM
PCD3359A
7.5.5
E
RASE PAGE
The EEPROM flags are set as described in Section 7.5.1.
The corresponding page bytes are erased.
The last instruction also starts Timer 2. Erasure takes
5 ms. A single-byte erase is simply a special case of ‘erase
page’.
Note that ADDR does not auto-increment after an erase
cycle.
Table 23
Erase page
7.6
Timer 2
Timer 2 is a 8-bit down-counter decremented at a rate of
1
480
×
f
xtal
. It may be used either for EEPROM timing or as
a general purpose timer. Conflicts between the two
applications should be carefully avoided.
7.6.1
T
IMER
2
FOR
EEPROM
TIMING
When used for EEPROM timing, Timer 2 serves to
generate the 5 ms intervals needed for erasing or writing
the EEPROM. At the decrement rate of
1
480
×
f
xtal
, the
reload value for a 5 ms interval is a function of f
xtal
.
Table 24 summarizes the required reload values for a
number of oscillator frequencies.
Timer 2 is started by setting bit EWP in the EPCR.
The Timer Register T2 is loaded with the reload value from
RELR. T2 decrements to zero.
For an erase/write cycle, underflow of T2 indicates the end
of the erase operation. Therefore, Timer Register T2 is
reloaded from RELR for another 5 ms interval during
which the flagged EEPROM latches are copied to the
corresponding bytes in the page addressed by ADDR.
The second underflow of an erase/write cycle and the first
underflow of write page and erase page conclude the
corresponding EEPROM cycle. Timer 2 is stopped, T2F is
set whereas EWP and MC1 to MC3 are cleared.
INSTRUCTION
RESULT
MOV A, #EWP + MC3 + MC2 + MC1
‘erase page’
control word
start ‘erase
page’ cycle
MOV EPCR, A
Table 24
Reload values as a function of f
xtal
Note
1.
The reload value is (5
×
10
3
×
1
480
f
xtal
)
1;
f
xtal
in MHz.
7.6.2
T
IMER
2
AS A GENERAL PURPOSE TIMER
When used for purposes other than EEPROM timing,
Timer 2 is started by setting STT2. The Timer Register T2
(see Table 26) is loaded with the reload value from RELR.
T2 decrements to zero. On underflow, T2 is reloaded from
RELR, T2F is set and T2 continues to decrement.
Timer 2 can be stopped at any time by clearing STT2.
The value of T2 is then held and can be read out. After
setting STT2 again, Timer 2 decrements from the reload
value. Alternatively, it is possible to read T2 ‘on the fly’ i.e.
while Timer 2 is operating.
f
xtal
(MHz)
RELOAD VALUE
(1)
(HEX)
1
2
0A
14
25
3E
68
A6
3.58
6
10
16
相關PDF資料 |
PDF描述 |
|---|---|
| PCD3359AH | 8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| PCD3359AP | 8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| PCD3359AT | 8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| PCD3360 | Programmable multi-tone telephone ringer |
| PCD3360P | Programmable multi-tone telephone ringer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD3359AH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| PCD3359AP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| PCD3359AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| PCD3360 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Programmable multi-tone telephone ringer |
| PCD3360P | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Programmable multi-tone telephone ringer |
發布緊急采購，3分鐘左右您將得到回復。