- 您現在的位置：買賣IC網 > PDF目錄382375 > PC2119VU (NXP Semiconductors N.V.) KPTC 23C 21#20 2#16 PIN PLUG PDF資料下載
參數資料
| 型號： | PC2119VU |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | KPTC 23C 21#20 2#16 PIN PLUG |
| 中文描述： | LCD控制器/驅動器 |
| 文件頁數： | 25/60頁 |
| 文件大?。?/td> | 260K |
| 代理商： | PC2119VU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
1999 Mar 02
25
Philips Semiconductors
Product specification
LCD controllers/drivers
PCF2119x
8.4
Display control (and partial power-down mode)
8.4.1
D
The display is on when D = 1 and off when D = 0. Display
data in the DDRAM is not affected and can be displayed
immediately by setting D to a logic 1.
When the display is off (D = 0) the chip is in partial
power-down mode:
The LCD outputs are connected to V
SS
The LCD generator and bias generator are turned off.
Three oscillator cycles are required after sending the
‘display off’ instruction to ensure all outputs are at V
SS
,
afterwards OSC can be stopped. If the oscillator is running
during partial power-down mode (‘display off’) the chip can
still execute instructions. Even lower current consumption
is obtained by inhibiting the oscillator (OSC = V
SS
).
To ensure I
DD
<1
μ
A, the parallel bus pads DB7 to DB0
should be connected to V
DD
; RS and R/W to V
DD
or left
open-circuit and PD to V
DD
. Recovery from power-down
mode: PD back to logic 0, if necessary OSC back to V
DD
and send a ‘display control’ instruction with D = 1.
8.4.2
C
The cursor is displayed when C = 1 and inhibited when
C = 0. Even if the cursor disappears, the display functions
I/D, etc. remain in operation during display data write.
The cursor is displayed using 5 dots in the 8th line
(see Fig.5).
8.4.3
B
The character indicated by the cursor blinks when B = 1.
The cursor character blink is displayed by switching
between display characters and all dots on with a period of
approximately 1 second, with
The cursor underline and the cursor character blink can be
set to display simultaneously.
f
blink
f
52224
----------------
=
8.5
Cursor or display shift
‘Cursor/display shift’ moves the cursor position or the
display to the right or left without writing or reading display
data. This function is used to correct a character or move
the cursor through the display. In 2-line displays, the
cursor moves to the next line when it passes the last
position (40) of the line. When the displayed data is shifted
repeatedly all lines shift at the same time; displayed
characters do not shift into the next line.
The Address Counter (AC) content does not change if the
only action performed is shift display, but increments or
decrements with the ‘cursor shift’.
8.6
Function set
8.6.1
DL (
PARALLEL MODE ONLY
)
Sets interface data width. Data is sent or received in bytes
(DB7 to DB0) when DL = 1 or in two nibbles (DB7 to DB4)
when DL = 0. When 4-bit width is selected, data is
transmitted in two cycles using the parallel bus. In a 4-bit
application DB3 to DB0 should be left open-circuit (internal
pull-ups). Hence in the first ‘function set’ instruction after
power-on, N and H are set to logic 1. A second ‘function
set’ must then be sent (2 nibbles) to set N and H to their
required values.
‘Function set’ from the I
2
C-bus interface sets the DL bit to
logic 1.
8.6.2
M
Selects either 1-line by 32 display (M = 0) or 2-line by
16 display (M = 1).
8.6.3
SL
Selects MUX 1 : 9, 1-line by 16 display (independent of
M and L). Only rows 1 to 8 and 17 are to be used. All other
rows must be left open-circuit. The DDRAM map is the
same as in the 2-line by 16 display mode, however, the
second line is not displayable.
相關PDF資料 |
PDF描述 |
|---|---|
| PC2402LRS-ANH-H | (75.35 k) |
| PC27001 | Electronic Circuit Breaker |
| PC27005 | Electronic Circuit Breaker |
| PC27007 | Electronic Circuit Breaker |
| PC27007.5-4700 | Electronic Circuit Breaker |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PC2119VU/2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
| PC-211-E-69 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| PC212 | 制造商:Thomas Betts 功能描述:Exact Equal/ 1-5 Days |
| PC2-120-LS1 | 制造商:GRASSLIN CONTROLS INTERMATIC 功能描述:LIGHT CONTROLLER, SWITCH W/ LS1 SENSOR |
| PC2-120P | 制造商:Amphenol Corporation 功能描述:CONN RECTANGULAR SKT 120 POS 2.54MM SLDR RA TH - Bulk 制造商:Amphenol Corporation 功能描述:PCB 2 ROWS 120 CONT |
發布緊急采購，3分鐘左右您將得到回復。