- 您現在的位置：買賣IC網 > PDF目錄12046 > P89LPC9103FTK,115 (NXP Semiconductors)IC 80C51 MCU FLASH 1K 10-HVSON PDF資料下載
參數資料
| 型號： | P89LPC9103FTK,115 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 27/39頁 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 1K 10-HVSON |
| 產品培訓模塊： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 標準包裝： | 1 |
| 系列： | LPC900 |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | UART/USART |
| 外圍設備： | 欠壓檢測/復位，LED，POR，PWM，WDT |
| 輸入/輸出數： | 8 |
| 程序存儲器容量： | 1KB（1K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 128 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 數據轉換器： | A/D 4x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 包裝： | 標準包裝 |
| 配用： | 622-1008-ND - BOARD FOR LPC9103 10-HVSON 622-1006-ND - SOCKET ADAPTER BOARD 622-1004-ND - BOARD DEMO FOR PHILIPS PCA9633 622-1003-ND - KIT FOR LCD DEMO 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X |
| 其它名稱： | 568-2001-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
P89LPC9102_9103_9107_3
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 03 — 10 July 2007
33 of 61
NXP Semiconductors
P89LPC9102/9103/9107
8-bit microcontrollers with two-clock accelerated 80C51 core
After power-up all I/O pins, except P1.5, may be congured by software.
Pin P1.5 is input-only.
Every output on the P89LPC9102/9103/9107 has been designed to sink typical LED drive
current. However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to Table 12 “Static characteristics” for detailed specications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
8.13 Power monitoring functions
The P89LPC9102/9103/9107 incorporates power monitoring functions designed to
prevent incorrect operation during initial power-up and power loss or reduction during
operation. This is accomplished with two hardware functions: Power-on Detect and
Brownout detect.
8.13.1 Brownout detection
The Brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a Brownout detection to cause a processor reset,
however, it may alternatively be congured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If Brownout detection is enabled, the brownout condition occurs when VDD falls below the
rises above Vbo. If the P89LPC9102/9103/9107 device is to operate with a power supply
that can be below 2.7 V, Brownout detect Enable (BOE) should be left in the
unprogrammed state so that the device can operate at 2.4 V, otherwise continuous
brownout reset may prevent the device from operating.
For correct activation of Brownout detect, the VDD rise and fall times must be observed.
Please see Table 12 “Static characteristics” for specications.
8.13.2 Power-on detection
The Power-on Detect has a function similar to the Brownout detect, but is designed to
work as power comes up initially, before the power supply voltage reaches a level where
Brownout detect can work. The Power-on detect ag (POF) in the RSTSRC register is set
to indicate an initial power-up condition. The POF ag will remain set until cleared by
software.
8.14 Power reduction modes
The P89LPC9102/9103/9107 supports three different power reduction modes. These
modes are Idle mode, Power-down mode, and Total Power-down mode.
8.14.1 Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle
mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 861257-1 | CONN RCPT W/FLANGE FEED-THRU TIN |
| VI-J6W-IX-B1 | CONVERTER MOD DC/DC 5.5V 75W |
| ATMEGA324PA-MU | MCU AVR 32K FLASH 44-QFN |
| VJ1825A223JBAAT4X | CAP CER 0.022UF 50V 5% NP0 1825 |
| VI-J6B-IX-B1 | CONVERTER MOD DC/DC 95V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC9107 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock accelerated 80C51 core 1 kB 3 V byte-erasable flash with 8-bit A/D converter |
| P89LPC9107FDH | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 1K FLASH TSSOP14 |
| P89LPC9107FDH,129 | 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC9107FDH129 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ TSSOP-14 |
| P89LPC9107FN | 功能描述:8位微控制器 -MCU 1KFL/128B RAM/8B ADC/PWM/UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。