參數資料
型號： P80C32SBAA
廠商： NXP Semiconductors N.V.
元件分類： 存儲器
英文描述： 80C51 8-bit microcontroller family 128-256 byte RAM ROMless low voltage (2.7 V-5.5 V), low power, high speed (33 MHz)
封裝： P80C31SBAA<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html<1<week 44, 2004,;P80C31SBPN<SOT129-1 (DIP40)|<<http://www.nxp.com/packages/SOT129-1.html<1<
文件頁數： 6/32頁
文件大?。?/td> 232K
代理商： P80C32SBAA
Philips Semiconductors
Product specification
80C31/80C32
80C51 8-bit microcontroller family
128/256 byte RAM ROMless low voltage (2.7V–5.5V),
low power, high speed (33 MHz)
2000 Aug 07
6
PIN DESCRIPTIONS
PIN NUMBER
DIP
LCC
20
40
39–32
43–36
MNEMONIC
V
SS
V
CC
P0.0–0.7
QFP
16
38
37–30
TYPE
I
I
I/O
NAME AND FUNCTION
Ground:
0 V reference.
Power Supply:
This is the power supply voltage for normal, idle, and power-down operation.
Port 0:
Port 0 is an open-drain, bidirectional I/O port with Schmitt trigger inputs. Port 0 pins
that have 1s written to them float and can be used as high-impedance inputs. Port 0 is also
the multiplexed low-order address and data bus during accesses to external program and
data memory. In this application, it uses strong internal pull-ups when emitting 1s.
Port 1:
Port 1 is an 8-bit bidirectional I/O port with internal pull-ups and Schmitt trigger
inputs. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, port 1 pins that are externally pulled low will source
current because of the internal pull-ups. (See DC Electrical Characteristics: I
IL
). Alternate
functions for Port 1 include:
T2 (P1.0):
Timer/Counter 2 external count input/clockout (see Programmable Clock-Out)
T2EX (P1.1):
Timer/Counter 2 Reload/Capture/Direction control
Port 2:
Port 2 is an 8-bit bidirectional I/O port with internal pull-ups and Schmitt trigger
inputs. Port 2 pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source
current because of the internal pull-ups. (See DC Electrical Characteristics: I
). Port 2 emits
the high-order address byte during fetches from external program memory and during
accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this
application, it uses strong internal pull-ups when emitting 1s. During accesses to external
data memory that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2
special function register.
Port 3:
Port 3 is an 8-bit bidirectional I/O port with internal pull-ups and Schmitt trigger
inputs. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and
can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source
current because of the pull-ups. (See DC Electrical Characteristics: I
IL
). Port 3 also serves
the special features of the 80C51 family, as listed below:
RxD (P3.0):
Serial input port
TxD (P3.1):
Serial output port
INT0 (P3.2):
External interrupt
INT1 (P3.3):
External interrupt
T0 (P3.4):
Timer 0 external input
T1 (P3.5):
Timer 1 external input
WR (P3.6):
External data memory write strobe
RD (P3.7):
External data memory read strobe
Reset:
A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to V
SS
permits a power-on reset using only an external
capacitor to V
CC
.
Address Latch Enable:
Output pulse for latching the low byte of the address during an
access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 the
oscillator frequency, and can be used for external timing or clocking. Note that one ALE
pulse is skipped during each access to external data memory. ALE can be disabled by
setting SFR auxiliary.0. With this bit set, ALE will be active only during a MOVX instruction.
Program Store Enable:
The read strobe to external program memory. When the 80C31/32
is executing code from the external program memory, PSEN is activated twice each
machine cycle, except that two PSEN activations are skipped during each access to
external data memory. PSEN is not activated during fetches from internal program memory.
External Access Enable/Programming Supply Voltage:
EA must be externally held low
to enable the device to fetch code from external program memory locations 0000H to
0FFFH.
Crystal 1:
Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
Crystal 2:
Output from the inverting oscillator amplifier.
22
44
P1.0–P1.7
1–8
2–9
40–44,
1–3
I/O
1
2
2
3
40
41
I/O
I
I/O
P2.0–P2.7
21–28
24–31
18–25
P3.0–P3.7
10–17
11,
13–19
5,
7–13
I/O
10
11
12
13
14
15
16
17
9
11
13
14
15
16
17
18
19
10
5
7
8
9
10
11
12
13
4
I
O
I
I
I
I
O
O
I
RST
ALE
30
33
27
O
PSEN
29
32
26
O
EA/V
PP
31
35
29
I
XTAL1
19
21
15
I
XTAL2
NOTE:
To avoid “l(fā)atch-up” effect at power-on, the voltage on any pin at any time must not be higher than V
CC
+ 0.5 V or V
SS
– 0.5 V, respectively.
18
20
14
O
相關PDF資料
PDF描述
PA140 HIGH VOLTAGE POWER OPERATIONAL AMPLIFIER
PAB2CA-3D-01-S FLUX LED LAMPS
PAY2CA-3B-02 FLUX LED LAMPS
PAY3CA-1B-02-S FLUX LED LAMPS
PAV4CA-1B-02-S FLUX LED LAMPS
相關代理商/技術參數
參數描述
P80C32SBAA,512 功能描述:8位微控制器 -MCU 80C51 256B 16MHZ ROMLESS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P80C32SBAA 制造商:NXP Semiconductors 功能描述:
P80C32SBAA512 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 16MHZ LCC-44
P80C32SBAA-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P80C32SBBB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*