參數資料
型號: P80C32SBAA
廠商: NXP Semiconductors N.V.
元件分類: 存儲器
英文描述: 80C51 8-bit microcontroller family 128-256 byte RAM ROMless low voltage (2.7 V-5.5 V), low power, high speed (33 MHz)
封裝: P80C31SBAA<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html<1<week 44, 2004,;P80C31SBPN<SOT129-1 (DIP40)|<<http://www.nxp.com/packages/SOT129-1.html<1<
文件頁數: 15/32頁
文件大?。?/td> 232K
代理商: P80C32SBAA
Philips Semiconductors
Product specification
80C31/80C32
80C51 8-bit microcontroller family
128/256 byte RAM ROMless low voltage (2.7V–5.5V),
low power, high speed (33 MHz)
2000 Aug 07
15
and 1 and exclude Slave 2 use address 1110 0100, since it is
necessary to make bit 2 = 1 to exclude slave 2.
The Broadcast Address for each slave is created by taking the
logical OR of SADDR and SADEN. Zeros in this result are trended
as don’t-cares. In most cases, interpreting the don’t-cares as ones,
the broadcast address will be FF hexadecimal.
Upon reset SADDR (SFR address 0A9H) and SADEN (SFR
address 0B9H) are leaded with 0s. This produces a given address
of all “don’t cares” as well as a Broadcast address of all “don’t
cares”. This effectively disables the Automatic Addressing mode and
allows the microcontroller to use standard 80C51 type UART drivers
which do not make use of this feature.
SCON
Address = 98H
Reset Value = 0000 0000B
SM0/FE
7
SM1
6
SM2
5
REN
4
TB8
3
RB8
2
Tl
1
Rl
0
Bit Addressable
(SMOD0 = 0/1)*
Symbol
Function
FE
Framing Error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit.
Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)
Serial Port Mode Bit 1
SM0
SM1
Mode
Description
Baud Rate**
0
0
0
shift register
f
OSC
/12
0
1
1
8-bit UART
variable
1
0
2
9-bit UART
f
OSC
/64 or f
OSC
/32
1
1
3
9-bit UART
variable
Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the
received 9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address.
In Mode 1, if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a
Given or Broadcast Address. In Mode 0, SM2 should be 0.
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired.
In modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received.
In Mode 0, RB8 is not used.
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the
other modes, in any serial transmission. Must be cleared by software.
Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in
the other modes, in any serial reception (except see SM2). Must be cleared by software.
SM0
SM1
SM2
REN
TB8
RB8
Tl
Rl
NOTE:
*SMOD0 is located at PCON6.
**f
OSC
= oscillator frequency
SU00043
Bit:
Figure 7. SCON: Serial Port Control Register
相關PDF資料
PDF描述
PA140 HIGH VOLTAGE POWER OPERATIONAL AMPLIFIER
PAB2CA-3D-01-S FLUX LED LAMPS
PAY2CA-3B-02 FLUX LED LAMPS
PAY3CA-1B-02-S FLUX LED LAMPS
PAV4CA-1B-02-S FLUX LED LAMPS
相關代理商/技術參數
參數描述
P80C32SBAA,512 功能描述:8位微控制器 -MCU 80C51 256B 16MHZ ROMLESS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P80C32SBAA 制造商:NXP Semiconductors 功能描述:
P80C32SBAA512 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 16MHZ LCC-44
P80C32SBAA-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P80C32SBBB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families