參數資料
型號： P1553ACRP
英文描述： MCU CMOS 20 LD 4MHZ 1K FLASH, -40C to +85C, 20-SSOP 208mil, TUBE
中文描述： SIDAC的| 180V五（公報）最大| 800mA的我（縣）|對220VAR
文件頁數： 99/161頁
文件大小： 986K
代理商： P1553ACRP
SIDACtor
Data Book
UL 1950 3RD Edition/CSA C22.2 No. 950-95
Teccor Electronics
(972) 580-7777
4 - 25
R
R
5.
Spacing
- Applies to parts in the TNV circuits that might ignite under over-
voltage conditions. Spacing requirements mandate that parts be separated
from internal materials of flammability class V-2 or lower, by at least 25mm of
air or a barrier material of flammability class V-1 or better. Parts should also be
separated from openings in the top or sides of the enclosure by at least 25mm
of air or a material barrier.
6.
Over-Voltage Tests
- Equipment may be subject to the tests in Table 4-18 which
are designed to simulate contact with primary power, short term induction as a
result of a primary power fault to a multi-earth neutral, a long duration power
fault to ground, and direct contact between the power mains and a
telecommunications cable.
Figure 4-11 Over-Voltage Flowchart
Over-Voltage Test Procedures
The following criteria is used when applying the over-voltage tests found in Table 4-18:
1.
Test Set-Up
- Equipment is to be mounted as it is intended to be used. Tests
may be conducted on either the equipment as an assembly, individual
subassemblies, or a partial assembly containing those components which may
be exposed to an over-voltage condition.
2.
Indicators
- Before testing, two single pieces of cheesecloth are to be wrapped
tightly around the assembly, subassembly, or partial assembly. The
cheesecloth acts as an indicator for conditions that may result in fire.
No
No
No
No
No
Yes
2
-S
100 A
1a
No Overvoltage Testing
Connects to Outside Cable
Yes
Yes
Li1.3 A
1b
26 AWG
Yes
Pass 1
Yes
Pass 6.3.3
2
Fire Enclosure
3
Yes
Yes
Acceptable
EnFire
No
No
Yes
Pass 5
4
Pass 2
5
Yes
No
No
No
Yes
AccNot
相關PDF資料
PDF描述
P1602AA MCU CMOS 18 LD 20MHZ 1K FLASH, 0C to +70C, 18-SOIC 300mil, T/R
P1602AARP MCU CMOS 18 LD 20MHZ 1K FLASH, -40C to +85C, 18-SOIC 300mil, T/R
P1602AB MCU CMOS 18 LD LOW PWR, 0C to +70C, 18-SOIC 300mil, TUBE
P1800EA MCU CMOS 44 LD 20MHZ 4K FLASH, 0C to +70C, 44-PLCC, TUBE
P1800EARP1 MCU CMOS 44 LD 20MHZ 4K FLASH, 0C to +70C, 44-MQFP, TRAY
相關代理商/技術參數
參數描述
P1553U 制造商:TECCOR 制造商全稱:TECCOR 功能描述:solid state crowbar devices
P1553U_L 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Balanced Three-chip SIDACtor
P1553UALRP 功能描述:硅對稱二端開關元件 3Chp 130V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1553UALTP 功能描述:硅對稱二端開關元件 3Chp 130V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1553UALXX 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:The series provides a single port surface mount solution that enables voice
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*