參數資料
型號： P1553ACRP
英文描述： MCU CMOS 20 LD 4MHZ 1K FLASH, -40C to +85C, 20-SSOP 208mil, TUBE
中文描述： SIDAC的| 180V五（公報）最大| 800mA的我（縣）|對220VAR
文件頁數： 109/161頁
文件大?。?/td> 986K
代理商： P1553ACRP
SIDACtor
Data Book
UL 497B
Teccor Electronics
(972) 580-7777
4 - 35
R
R
5,#&<+
Overview
UL 497B provides requirements for protectors which are used in communication and
fire alarm circuits. All SIDACtors are evaluated against this standard as individual
components and are listed as UL 497B compliant devices under UL file No. E133083.
Construction and Performance
UL 497B is divided into two sections covering construction and performance
requirements. Table 4-22 lists the contents of each main section.
Table 4-22 UL497B
Performance Requirements Specific to the SIDACtor
1.
Strike Voltage Breakdown Test
- Protectors are required to breakdown within the
manufacturers specified breakdown range or within 10% of a nominal single
breakdown voltage rating (Figure 4-18).
2.
Endurance Conditioning
- Protectors are subjected to 50 impulse cycles. Each
cycle is a 1000V
PK
, 10A, 10x1000μs pulse. Pulses are applied in one polarity at
10 second intervals, and then repeated in the opposite polarity.
3.
Variable Ambient Conditioning
- Protectors must comply with the strike voltage
requirements after being subjected to an ambient temperature of 0
°
C for 4
hours and again after being subjected to an ambient temperature of 49
°
C for an
additional 4 hours.
4.
Discharge Test
- Protectors must comply with strike voltage requirements after
being subjected to five successive discharges from a 2μF capacitor charged to
1000V
DC
(Figure 4-19).
Construction
Performance
General
General
Corrosion protection
Strike Voltage Breakdown
Field-Wiring Connections
Endurance Conditioning
Components
Temperature Test
Spacing
Dielectric Voltage-Withstand test
Fuses
Vibration Conditioning
Jarring Test
Discharge Test
Repeated Discharge Test
Polymeric Materials Test
High Temperature Test
Marking
相關PDF資料
PDF描述
P1602AA MCU CMOS 18 LD 20MHZ 1K FLASH, 0C to +70C, 18-SOIC 300mil, T/R
P1602AARP MCU CMOS 18 LD 20MHZ 1K FLASH, -40C to +85C, 18-SOIC 300mil, T/R
P1602AB MCU CMOS 18 LD LOW PWR, 0C to +70C, 18-SOIC 300mil, TUBE
P1800EA MCU CMOS 44 LD 20MHZ 4K FLASH, 0C to +70C, 44-PLCC, TUBE
P1800EARP1 MCU CMOS 44 LD 20MHZ 4K FLASH, 0C to +70C, 44-MQFP, TRAY
相關代理商/技術參數
參數描述
P1553U 制造商:TECCOR 制造商全稱:TECCOR 功能描述:solid state crowbar devices
P1553U_L 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Balanced Three-chip SIDACtor
P1553UALRP 功能描述:硅對稱二端開關元件 3Chp 130V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1553UALTP 功能描述:硅對稱二端開關元件 3Chp 130V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1553UALXX 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:The series provides a single port surface mount solution that enables voice
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*