- 您現在的位置：買賣IC網 > PDF目錄299576 > OR3T80-4BA352 FPGA, 484 CLBS, 58000 GATES, 80 MHz, PBGA352 PDF資料下載
參數資料
| 型號： | OR3T80-4BA352 |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 484 CLBS, 58000 GATES, 80 MHz, PBGA352 |
| 封裝： | PLASTIC, BGA-352 |
| 文件頁數： | 199/210頁 |
| 文件大?。?/td> | 2138K |
| 代理商： | OR3T80-4BA352 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁當前第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
Lucent Technologies Inc.
89
Preliminary Data Sheet, Rev. 1
September 1998
ORCA Series 3 FPGAs
FPGA Configuration Modes (continued)
Master Serial Mode
In the master serial mode, the FPGA loads the configu-
ration data from an external serial ROM. The configura-
tion data is either loaded automatically at start-up or on
a PRGM command to reconfigure. The ATT1700A
Series Serial PROMs can be used to configure the
FPGA in the master serial mode. This provides a sim-
ple 4-pin interface in a compact package.
Configuration in the master serial mode can be done at
powerup and/or upon a configure command. The sys-
tem or the FPGA must activate the serial ROM's
RESET
/OE and CE inputs. At powerup, the FPGA and
serial ROM each contain internal power-on reset cir-
cuitry that allows the FPGA to be configured without
the system providing an external signal. The power-on
reset circuitry causes the serial ROM's internal address
pointer to be reset. After powerup, the FPGA automati-
cally enters its initialization phase.
The serial ROM/FPGA interface used depends on such
factors as the availability of a system reset pulse, avail-
ability of an intelligent host to generate a configure
command, whether a single serial ROM is used or mul-
tiple serial ROMs are cascaded, whether the serial
ROM contains a single or multiple configuration pro-
grams, etc. Because of differing system requirements
and capabilities, a single FPGA/serial ROM interface is
generally not appropriate for all applications.
Data is read in the FPGA sequentially from the serial
ROM. The DATA output from the serial ROM is con-
nected directly into the DIN input of the FPGA. The
CCLK output from the FPGA is connected to the CLK
input of the serial ROM. During the configuration pro-
cess, CCLK clocks one data bit on each rising edge.
Since the data and clock are direct connects, the
FPGA/serial ROM design task is to use the system or
FPGA to enable the RESET/OE and CE of the serial
ROM(s). There are several methods for enabling the
serial ROM’s RESET/OE and CE inputs. The serial
ROM’s RESET/OE is programmable to function with
RESET active-high and OE active-low or RESET active-
low and OE active-high.
In Figure 55, serial ROMs are cascaded to configure
multiple daisy-chained FPGAs. The host generates a
500 ns low pulse into the FPGA's PRGM input. The
FPGA’s INIT input is connected to the serial ROMs’
RESET
/OE input, which has been programmed to
function with RESET active-low and OE active-high.
The FPGA DONE is routed to the CE pin. The low on
DONE enables the serial ROMs. At the completion of
configuration, the high on the FPGA's DONE disables
the serial ROM.
Serial ROMs can also be cascaded to support the con-
figuration of multiple FPGAs or to load a single FPGA
when configuration data requirements exceed the
capacity of a single serial ROM. After the last bit from
the first serial ROM is read, the serial ROM outputs
CEO
low and 3-states the DATA output. The next serial
ROM recognizes the low on CE input and outputs con-
figuration data on the DATA output. After configuration
is complete, the FPGA’s DONE output into CE disables
the serial ROMs.
This FPGA/serial ROM interface is not used in applica-
tions in which a serial ROM stores multiple configura-
tion programs. In these applications, the next
configuration program to be loaded is stored at the
ROM location that follows the last address for the pre-
vious configuration program. The reason the interface
in Figure 55 will not work in this application is that the
low output on the INIT signal would reset the serial
ROM address pointer, causing the first configuration to
be reloaded.
In some applications, there can be contention on the
FPGA's DIN pin. During configuration, DIN receives
configuration data, and after configuration, it is a user
I/O. If there is contention, an early DONE at start-up
(selected in
ORCA Foundry) may correct the problem.
An alternative is to use LDC to drive the serial ROM's
CE
pin. In order to reduce noise, it is generally better to
run the master serial configuration at 1.25 MHz (M3 pin
tied high), rather than 10 MHz, if possible.
Figure 55. Master Serial Configuration Schematic
ATT1700A
DIN
M2
M1
M0
ORCA
SERIES
FPGA
CCLK
DOUT
TO DAISY-
CHAINED
DEVICES
DATA
CLK
CE
CEO
ATT1700A
DATA
CLK
RESET/OE
CEO
CE
TO MORE
SERIAL ROMs
AS NEEDED
DONE
INIT
PROGRAM
RESET/OE
PRGM
5-4456.1(F)
相關PDF資料 |
PDF描述 |
|---|---|
| OR3T125-4BC432I | FPGA, 784 CLBS, 92000 GATES, 80 MHz, PBGA432 |
| OR3T80-4BC432I | FPGA, 484 CLBS, 58000 GATES, 80 MHz, PBGA432 |
| OR3C80-4BC600I | FPGA, 484 CLBS, 58000 GATES, 80 MHz, PBGA600 |
| OR3C80-5BC600I | FPGA, 484 CLBS, 58000 GATES, 80 MHz, PBGA600 |
| OR3T125-4BC600I | FPGA, 784 CLBS, 92000 GATES, 80 MHz, PBGA600 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OR3T80-4BC432I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T80-4BC600I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T80-4PS208I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T80-4PS240I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T80-5BA352 | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。