- 您現在的位置：買賣IC網 > PDF目錄361135 > NRF9E5-EVKIT915 (Electronic Theatre Controls, Inc.) 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC PDF資料下載
參數資料
| 型號： | NRF9E5-EVKIT915 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC |
| 中文描述： | 433/868/915MHz RF收發器與8051兼容的嵌入式微控制器和4輸入，10位ADC |
| 文件頁數： | 75/104頁 |
| 文件大小： | 1436K |
| 代理商： | NRF9E5-EVKIT915 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
PRODUCT SPECIFICATION
nRF9E5 Single Chip Transceiver with Embedded Microcontroller and ADC
Main office: Nordic Semiconductor ASA - Vestre Rosten 81, N-7075 Tiller, Norway -Phone +4772898900 - Fax +4772898989
Revision: 1.1
Page 75 of 104
June 2004
Bit
TCON.7
Function
TF1 - Timer 1 overflow flag. Set to 1 when the Timer 1 count overflows and cleared when
the CPU vectors to the interrupt service routine.
TR1 - Timer 1 run control. Set to 1 to enable counting on Timer 1.
TF0 - Timer 0 overflow flag. Set to 1 when the Timer 0 count overflows and cleared when
the CPU vectors to the interrupt service routine.
TR0 - Timer 0 run control. Set to 1 to enable counting on Timer 0.
IE1 - Interrupt 1 edge detect. If external interrupt 1 is configured to be edge-sensitive (IT1
= 1), IE1 is set by hardware when a negative edge is detected on the INT1_N external
interrupt pin and is automatically cleared when the CPU vectors to the corresponding
interrupt service routine. In edge-sensitive mode, IE1 can also be cleared by software.
If external interrupt 1 is configured to be level-sensitive (IT1 = 0), IE1 is set when the
INT1_N pin is low and cleared when the INT1_N pin is high. In level-sensitive mode,
software cannot write to IE1.
IT1 - Interrupt 1 type select. When IT1 = 1, the nRF9E5 detects external interrupt pin
INT1_N on the falling edge (edge-sensitive). When IT1 = 0, the nRF9E5 detects INT1_N
as a low level (level-sensitive).
IE0 - Interrupt 0 edge detect. If external interrupt 0 is configured to be edge-sensitive (IT0
= 1), IE0 is set by hardware when a negative edge is detected on the INT0_N external
interrupt pin and is automatically cleared when the CPU vectors to the corresponding
interrupt service routine. In edge-sensitive mode, IE0 can also be cleared by software.
If external interrupt 0 is configured to be level-sensitive (IT0 = 0), IE0 is set when the
INT0_N pin is low and cleared when the INT0_N pin is high. In level-sensitive mode,
software cannot write to IE0.
IT0 - Interrupt 0 type select. When IT1 = 1, the nRF9E5 detects external interrupt INT0_N
on the falling edge (edge-sensitive). When IT1 = 0, the nRF9E5 detects INT0_N as a low
level (level-sensitive).
TCON.6
TCON.5
TCON.4
TCON.3
TCON.2
TCON.1
TCON.0
Table 66 TCON Register – SFR 0x88.
18.8.1.1
Mode 0
Mode 0 operation, illustrated in Figure 18, is the same for Timer 0 and Timer 1. In mode
0, the timer is configured as a 13-bit counter that uses bits 0–4 of TL0 (or TL1) and all
eight bits of TH0 (or TH1). The timer enable bit (TR0/TR1) in the TCON SFR starts the
timer. The C/T bit selects the timer/counter clock source, CPU_clk or T0/T1. The timer
counts transitions from the selected source as long as the GATE bit is 0, or the GATE bit
is 1 and the corresponding interrupt pin (INT0_N or INT1_N) is deasserted. INT0_N
and INT1_N are alternate function bits of Port0, please see Table 8 Port functions. When
the 13-bit count increments from 0x1FFF (all ones), the counter rolls over to all zeros,
the TF0 (or TF1) bit is set in the TCON SFR, and the t0_out (or t1_out) pin goes high
for one clock cycle. The upper three bits of TL0 (or TL1) are indeterminate in mode 0
and must be masked when the software evaluates the register.
18.8.1.2
Mode 1
Mode 1 operation is the same for Timer 0 and Timer 1. In mode 1, the timer is
configured as a 16-bit counter. As illustrated in, all eight bits of the LSB register (TL0 or
TL1) are used. The counter rolls over to all zeros when the count increments from
0xFFFF. Otherwise, mode 1 operation is the same as mode 0.
相關PDF資料 |
PDF描述 |
|---|---|
| NRF9E5IC | 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC |
| NRN9S104JTS | SINGLE-IN-LINE SIP RESISTOR NETWORKS CONFORMAL COATED LOW PROFILE |
| NRN9xxx | SINGLE-IN-LINE SIP RESISTOR NETWORKS CONFORMAL COATED LOW PROFILE |
| NRN13xxx | SINGLE-IN-LINE SIP RESISTOR NETWORKS CONFORMAL COATED LOW PROFILE |
| NRN4S104JLS | SINGLE-IN-LINE SIP RESISTOR NETWORKS CONFORMAL COATED LOW PROFILE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NRF9E5IC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC |
| nRF9E5-REEL | 功能描述:射頻收發器 433/868/915MHz TRNSCVR RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| NRF-D | 制造商:IDEC 功能描述:35mmDINKi[pT[Lbgz_ Bulk 制造商:IDEC CORPORATION 功能描述:DIN RAIL MT.ADAPTOR |
| NRF-HEAD-CAP-B | 制造商:IDEC CORPORATION 功能描述:Circuit Protector |
| NRF-HEAD-CAP-W | 制造商:IDEC CORPORATION 功能描述:Circuit Protector |
發布緊急采購，3分鐘左右您將得到回復。