- 您現在的位置：買賣IC網 > PDF目錄359273 > NJU26175 (New Japan Radio Co., Ltd.) NJU26100 Series Hardware Specification PDF資料下載
參數資料
| 型號： | NJU26175 |
| 廠商： | New Japan Radio Co., Ltd. |
| 英文描述： | NJU26100 Series Hardware Specification |
| 中文描述： | NJU26100系列硬件規格 |
| 文件頁數： | 15/17頁 |
| 文件大小： | 270K |
| 代理商： | NJU26175 |
Ver.2005-02-24
NJU26100 Series
- 15 -
5.2 I
2
C Bus
When the NJU26100 Series is configured for I
2
C bus communication in GPIO0 pin (*SEL1 pin)=”Low”, the serial
host interface transfers data to the SDA pin and clocks data to the SCL pin. SDA is an open drain pin requiring an
external 4.7k pull-up resistor. AD1 and AD2 pins are used to configure the seven-bit SLAVE address of the serial
host interface. This offers additional flexibility to a system design by four different SLAVE addresses of the
NJU26100 Series. An address can be arbitrarily set up by the AD1, 2 pins. The I
2
C address of AD1, 2 is decided by
connection of AD1, 2 pins. The I
2
C address should be the same level of AD1, 2 pins. The real I
2
C address is
described in the each data sheet. Refer to the each data sheet.
* It excepts NJU26150. Refer to each data sheet.
Table 5-3 I
2
C Bus SLAVE Address
bit7
bit6
bit5
bit4
bit3
0
0
1
1
1
*1 The SLAVE address bit is 0 when ADx-pin is low level. The SLAVE address bit is 1 when ADx-pin is high level.
The figure on the following page shows the basic timing relationships for transfers. A transfer is initiated with a
START condition, followed by the SLAVE address byte. The SLAVE address consists of the seven-bit SLAVE
address followed by a read/write (R/W) bit. When an address with an effective serial host interface is detected, the
acknowledgement bit which sets a SDA line to Low in the ninth bit clock cycle is returned.
The R/W bit in the SLAVE address byte sets the direction of data transmission until a STOP condition terminates
the transfer. R/W = 0 indicates the host will send to the NJU26100 Series while R/W = 1 indicates the host will
receive data from the NJU26100 Series.
bit2
AD2*
1
bit1
AD1*
1
bit0
R/W
Fig. 5-2 I
2
C Bus Format
In case of the NJU26100 Series, only single-byte transmission is available.
The serial host interface supports “Standard-Mode (100kbps)” I
2
C bus data transfer.
1-7
8
9
1-7
8
9
S
P
SDA
SCL
Address
Data
ACK
ACK
R/W
Start
Stop
相關PDF資料 |
PDF描述 |
|---|---|
| NJW1165 | AUDIO PROCESSOR |
| NJW1165M | AUDIO PROCESSOR |
| NJW1165L | AUDIO PROCESSOR |
| NJW1167 | AUDIO PROCESSOR with Subwoofer Output |
| NJW1167V | AUDIO PROCESSOR with Subwoofer Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NJU26176 | 制造商:NJRC 制造商全稱:New Japan Radio 功能描述:NJU26100 Series Hardware Specification |
| NJU26177 | 制造商:NJRC 制造商全稱:New Japan Radio 功能描述:NJU26100 Series Hardware Specification |
| NJU26178 | 制造商:NJRC 制造商全稱:New Japan Radio 功能描述:NJU26100 Series Hardware Specification |
| NJU26179 | 制造商:NJRC 制造商全稱:New Japan Radio 功能描述:NJU26100 Series Hardware Specification |
| NJU26180 | 制造商:New Japan Radio Co Ltd (NJR/JRC) 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。