參數資料
型號: MT9075B
廠商: Mitel Networks Corporation
英文描述: E1 Single Chip Transceiver
中文描述: 素E1單芯片收發器
文件頁數: 60/78頁
文件大小: 347K
代理商: MT9075B
MT9075B
Preliminary Information
60
Table 88 - HDLC Status Register
(Pages 0BH & 0CH, Address 14H)
Bit
Name
Functional Description
3, 2
Txstat2,
Txstat1
Transmit
indicate the status of the TX FIFO
as follows:
Status.
These
bits
Txsta
t2
Txsta
t1
TX FIFO Status
0
0
TX FIFO full up to
the selected status
level or more. See
Table 93.
0
1
The number of bytes
in the TX FIFO has
reached
exceeded
selected
threshold level. See
Table 94.
or
the
interrupt
1
0
TX FIFO empty.
1
1
The number of bytes
in the TX FIFO is
less
than
selected
threshold level. See
Table 94.
the
interrupt
1, 0
Rxstat2,
Rxstat1
Receive
indicate the status of the RX FIFO
as follows:
Status.
These
bits
Rxsta
t2
Rxsta
t1
RX FIFO Status
0
0
RX FIFO empty.
0
1
The number of bytes
in the RX FIFO is
less
than
selected
level. See Table 94.
the
threshold
1
0
RX FIFO full up to
the selected status
level or more. See
Table 93.
1
1
The number of bytes
in the RX FIFO has
reached
exceeded
selected
threshold level. See
Table 94.
or
the
interrupt
Bit
Name
Functional Description
7
Intsel
(0)
Interrupt Selection.
When one, this
bit will cause bit 2 of the Interrupt
Register to reflect a TX FIFO
underrun (TXunder). When zero,
this interrupt will reflect a frame
abort (FA).
6
Cycle
(0)
When one, this bit will cause the
transmit byte count to cycle through
the value loaded into the Transmit
Byte Count Register.
5
Tcrci
(0)
Transmit CRC Inhibited
. When
one, this bit will inhibit transmission
of the CRC. That is, the transmitter
will not insert the computed CRC
onto the bit stream after seeing the
EOP tag byte. This is used in V.120
terminal adaptation for synchronous
protocol sensitive UI frames.
4
Seven
(0)
Seven Bits Address Recognition.
When one, this bit will enable seven
bits of address recognition in the
first address byte. The received
address byte must have bit 0 equal
to 1 which indicates a single
address byte is being received.
3
RSV
(0)
Reserved, must be zero for normal
operation.
2
RSV
(0)
Reserved, must be zero for normal
operation.
1
Rxfrst
(0)
RX FIFO Reset
. When one, the RX
FIFO will be reset. This causes the
receiver to be disabled until the next
reception of a flag. The status
register will identify the FIFO as
being empty. However, the actual
bit values in the RX FIFO will not be
reset.
0
Txfrst
(0)
TX FIFO Reset.
When one, the TX
FIFO will be reset. The Status
Register will identify the FIFO as
being empty. This bit will be reset
when data is written to the TX FIFO.
However, the actual bit values of
data in the TX FIFO will not be
reset. It is cleared by the next write
to the TX FIFO.
Table 89 - HDLC Control Register 2
(Pages 0BH & 0CH, Address 15H)
相關PDF資料
PDF描述
MT9075B E1 Single Chip Transceiver(E1單片收發器)
MT9075 E1 Single Chip Transceiver
MT9075A E1 Single Chip Transceiver
MT9075AL E1 Single Chip Transceiver
MT9075AP E1 Single Chip Transceiver
相關代理商/技術參數
參數描述
MT9075B-1 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:E1 Single Chip Transceiver
MT9075BL 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays
MT9075BL1 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 100MQFP 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 100MQFP
MT9075BP 制造商:Microsemi Corporation 功能描述:
MT9075BP1 制造商:Microsemi Corporation 功能描述:Single Chip Transceiver 1TX 1RX 2.048Mbps 68-Pin PLCC Tube 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 68PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE E1 SINGLE CHIP TRANSCEIVER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 68PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 68PLCC