- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9075B (Mitel Networks Corporation) E1 Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9075B |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | E1 Single Chip Transceiver |
| 中文描述： | 素E1單芯片收發器 |
| 文件頁數： | 19/78頁 |
| 文件大小： | 347K |
| 代理商： | MT9075B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
Preliminary Information
MT9075B
19
ones) are transmitted to indicate that the channel is
idle.
HDLC Transmitter
Following initialization and enabling, the transmitter
is in the Idle Channel state (Mark Idle), continuously
sending ones. Interframe Time Fill state (Flag Idle) is
selected by setting the Mark Idle bit in Control
Register 1 to one. The transmitter remains in either
of these two states until data is written to the TX
FIFO. Control Register 1 bits EOP (End Of Packet)
and FA (Frame Abort) are set as status bits before
the microprocessor loads 8 bits of data into the 10 bit
wide FIFO (8 bits data and 2 bits status). To change
the tag bits being loaded in the FIFO, Control
Register 1 must be written to before writing to the
FIFO. However, EOP and FA are reset after writing to
the TX FIFO. The Transmit Byte Count Register may
also be used to tag an EOP. The register is loaded
with the number of bytes in the packet and
decrements after every write to the Tx FIFO. When a
count of one is reached, the next byte written to the
FIFO is tagged as an end of packet. The register
may be made to cycle through the same count if the
packets are of the same length by setting Control
Register 2, bit Cycle (at address 15H of page 0BH
for HDLC0 or 0CH for HDLC1).
If the transmitter is in the Idle Channel state when
data is written to the TX FIFO, then an opening flag
is sent and data from TX FIFO follows. Otherwise,
data bytes are transmitted as soon as the current
flag byte has been sent. TX FIFO data bytes are
continuously transmitted until either the FIFO is
empty or an EOP or FA status bit is read by the
transmitter. After the last bit of the EOP byte has
been transmitted, a 16-bit FCS is sent followed by a
closing flag. When multiple packets of data are
loaded into TX FIFO, only one flag is sent between
packets.
Frame Aborts (FA, the transmission of 7F hex), are
transmitted by tagging a byte previously written to
the TX FIFO. When a byte has an FA tag, then an FA
is sent instead of that tagged byte. That is, all bytes
previous to but not including that byte are sent. After
an FA, the transmitter returns to the Mark Idle or
Interframe Time Fill state, depending on the state of
the Mark idle control bit.
TX FIFO underrun will occur if the FIFO empties and
the last byte did not have either an EOP or FA tag. A
frame abort sequence will be sent when an underrun
occurs.
Below is an example of the transmission of a three
byte packet (’AA’’03’’77’ hex) (Interframe time fill).
TxEN can be enabled before or after this sequence.
(a) Write’04’ to Control Register 1 - Mark Idle bit set
(b) Write’AA’ to Tx FIFO -Data byte
(c) Write’03’ to Tx FIFO - Data byte
(d) Write’34’ to Control Register 1 - TxEN; EOP;
Mark Idle bits set
(e) Write’77’ to Tx FIFO - Final data byte
The transmitter may be enabled independently of the
receiver. This is done by setting the TxEN bit of the
Control Register. Enabling happens immediately
upon writing to the register. Disabling using TxEN
will occur after the completion of the transmission of
the present packet; the contents of the FIFO are not
cleared. Disabling will consist of stopping the
transmitter clock. The Status and Interrupt Registers
may still be read, and the FIFO and Control
Registers may be written to while the transmitter is
disabled. The transmitted FCS may be inhibited
using the Tcrci bit of Control Register 2. In this mode
the opening flag followed by the data and closing flag
is sent and zero insertion is still included, but no
FCS. That is, the FCS is injected by the
microprocessor as part of the data field. This is used
in V.120 terminal adaptation for synchronous
protocol sensitive UI frames.
HDLC Receiver
After initialization and enabling, the receiver clocks in
serial data, continuously checking for Go-Aheads (0
1111 1110), flags (0111 1110), and Idle Channel
states (at least fifteen ones). When a flag is
detected, the receiver synchronizes itself to the
serial stream of data bits, automatically calculating
the FCS. If the data length between flags after zero
removal is less than 25 bits, then the packet is
ignored so no bytes are loaded into Rx FIFO
.
When
the data length after zero removal is between 25 and
31 bits, a first byte and bad FCS code are loaded
into the Rx FIFO. For an error-free packet, the result
in the CRC register should match the HEX pattern of
“F0B8” when a closing flag is detected.
If address recognition is required, the Receiver
Address Recognition Registers (address 10H and
11H) are loaded with the desired address and the
Adrec bit in the Control Register 1 (address 13H) is
set to one. Bit 0 of the Address Registers is used as
an enable bit for that byte, thus allowing either or
both of the first two bytes to be compared to the
expected values. In addition, seven bits of address
comparison can be realized on the first byte if this is
a single byte address by setting the Seven bit of
Control Register 2 (address 15H).
相關PDF資料 |
PDF描述 |
|---|---|
| MT9075B | E1 Single Chip Transceiver(E1單片收發器) |
| MT9075 | E1 Single Chip Transceiver |
| MT9075A | E1 Single Chip Transceiver |
| MT9075AL | E1 Single Chip Transceiver |
| MT9075AP | E1 Single Chip Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9075B-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:E1 Single Chip Transceiver |
| MT9075BL | 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays |
| MT9075BL1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 100MQFP 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 100MQFP |
| MT9075BP | 制造商:Microsemi Corporation 功能描述: |
| MT9075BP1 | 制造商:Microsemi Corporation 功能描述:Single Chip Transceiver 1TX 1RX 2.048Mbps 68-Pin PLCC Tube 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 68PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE E1 SINGLE CHIP TRANSCEIVER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 68PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 68PLCC |
發布緊急采購，3分鐘左右您將得到回復。