- 您現在的位置：買賣IC網 > PDF目錄385639 > MT46V8M8 (Micron Technology, Inc.) 2 Meg x 8 x 4 banks DDR SDRAM(2 M x 8 x 4組，雙數據速率同步動態RAM) PDF資料下載
參數資料
| 型號： | MT46V8M8 |
| 廠商： | Micron Technology, Inc. |
| 英文描述： | 2 Meg x 8 x 4 banks DDR SDRAM(2 M x 8 x 4組，雙數據速率同步動態RAM) |
| 中文描述： | 2梅格× 8 × 4銀行DDR SDRAM內存（2米× 8 × 4組，雙數據速率同步動態RAM）的 |
| 文件頁數： | 26/69頁 |
| 文件大?。?/td> | 2369K |
| 代理商： | MT46V8M8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
26
64Mb: x4, x8, x16 DDR SDRAM
64Mx4x8x16DDR_B.p65
–
Rev. B; Pub. 10/00
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2000, Micron Technology, Inc.
64Mb: x4, x8, x16
DDR SDRAM
WRITEs
WRITE bursts are initiated with a WRITE command,
as shown in Figure 14.
The starting column and bank addresses are pro-
vided with the WRITE command, and auto precharge is
either enabled or disabled for that access. If auto precharge
is enabled, the row being accessed is precharged at the
completion of the burst. For the generic WRITE com-
mands used in the following illustrations, auto precharge
is disabled.
During WRITE bursts, the first valid data-in element
will be registered on the first rising edge of DQS follow-
ing the WRITE command, and subsequent data ele-
ments will be registered on successive edges of DQS. The
LOW state on DQS between the WRITE command and
the first rising edge is known as the write preamble; the
LOW state on DQS following the last data-in element is
known as the write postamble.
The time between the WRITE command and the first
corresponding rising edge of DQS (
t
DQSS) is specified
with a relatively wide range (from 75 percent to 125
percent of one clock cycle). All of the WRITE diagrams
show the nominal case, and where the two extreme cases
(i.e.,
t
DQSS [MIN] and
t
DQSS
[MAX]) might not be
intuitive, they have also been included. Figure 15 shows
the nominal case and the extremes of
t
DQSS for a burst
of 4. Upon completion of a burst, assuming no other
commands have been initiated, the DQs will remain
High-Z and any additional input data will be ignored.
Data for any WRITE burst may be concatenated with
or truncated with a subsequent WRITE command. In
either case, a continuous flow of input data can be
maintained. The new WRITE command can be issued
on any positive edge of clock following the previous
WRITE command. The first data element from the new
burst is applied after either the last element of a com-
pleted burst or the last desired data element of a longer
burst which is being truncated. The new WRITE com-
mand should be issued
x
cycles after the first WRITE
command, where
x
equals the number of desired data
element pairs (pairs are required by the 2
n
-prefetch
architecture).
Figure 16 shows concatenated bursts of 4. An ex-
ample of nonconsecutive WRITEs is shown in Figure 17.
Full-speed random write accesses within a page or pages
can be performed as shown in Figure 18.
Data for any WRITE burst may be followed by a
subsequent READ command. To follow a WRITE with-
out truncating the WRITE burst,
t
WTR should be met as
shown in Figure 19.
Data for any WRITE burst may be truncated by a
subsequent READ command, as shown in Figure 20.
Note that only the data-in pairs that are registered prior
to the
t
WTR period are written to the internal array, and
Figure 14
WRITE Command
any subsequent data-in should be masked with DM as
shown in Figure 21.
Data for any WRITE burst may be followed by a
subsequent PRECHARGE command. To follow a WRITE
without truncating the WRITE burst,
t
WR should be
met as shown in Figure 22.
Data for any WRITE burst may be truncated by a
subsequent PRECHARGE command, as shown in Fig-
ures 23 and 24. Note that only the data-in pairs that are
registered prior to the
t
WR period are written to the
internal array, and any subsequent data-in should be
masked with DM as shown in Figures 23 and 24. After
the PRECHARGE command, a subsequent command to
the same bank cannot be issued until
t
RP is met.
CS#
WE#
CAS#
RAS#
CKE
CA
A10
BA0,1
HIGH
EN AP
DIS AP
BA
CK
CK#
CA = Column Address
BA = Bank Address
EN AP = Enable Auto Precharge
DIS AP = Disable Auto Precharge
DON
’
T CARE
x4: A0-A9
x8: A0-A8
x16: A0-A7
x4: A11
x8: A9, A11
x16: A8, A9, A11
相關PDF資料 |
PDF描述 |
|---|---|
| MT46V2M32LG | DOUBLE DATA RATE DDR SDRAM |
| MT46V2M32V1 | DOUBLE DATA RATE DDR SDRAM |
| MT46V32M4-1 | DOUBLE DATA RATE DDR SDRAM |
| MT46V32M4TG-75 | DOUBLE DATA RATE DDR SDRAM |
| MT46V32M4TG-75L | DOUBLE DATA RATE DDR SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT46VDCFG-T16A | 制造商:Micron Technology Inc 功能描述:SDRAM DDR SPECIAL/CUSTOM 46VDC FBGA 2.5V PLASTIC 256MEG - Trays |
| MT470 | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:TRUNCATED LED LAMPS |
| MT4700CF-UBL | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:Blue Visible Emitter |
| MT470-G | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:TRUNCATED LED LAMPS |
| MT470-R | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:TRUNCATED LED LAMPS |
發布緊急采購，3分鐘左右您將得到回復。