參數資料
型號： MRF24J40-IMM
廠商： Microchip Technology Inc.
英文描述： IEEE 802.15.4⑩ 2.4 GHz RF Transceiver
中文描述： IEEE 802.15.4標準⑩2.4 GHz射頻收發器
文件頁數： 54/66頁
文件大?。?/td> 748K
代理商： MRF24J40-IMM
MRF24J40
DS39776A-page 52
Advance Information
2006 Microchip Technology Inc.
A.2
PCB Layout Design
The following guidelines are intended to aid users who
are not experienced in high-frequency PCB layout
design.
The printed circuit board is comprised of four basic FR4
layers: signal layout, RF ground, power line routing and
ground (see Figure A-9). The guidelines will explain the
requirements of these layers.
FIGURE A-9:
FOUR BASIC COPPER FR4 LAYERS
It is important to keep the original PCB thickness
since any change will affect antenna performance
(see total thickness of dielectric) or microstrip
lines characteristic impedance.
The first layer width of a 50
Ω
characteristic
impedance microstrip line is 12 mils.
Avoid having microstrip lines longer than 2.5 cm,
since that line might get very close to a quarter
wave length of the working frequency of the board
which is 3.0 cm, and start behaving as an
antenna.
Except for the antenna layout, avoid sharp
corners since they can act as an antenna. Round
corners will eliminate possible future EMI
problems.
Digital lines by definition are prone to be very
noisy when handling periodic waveforms and fast
clock/switching rates. Avoid laying out a RF signal
close to any digital lines.
A via filled ground patch underneath the IC
transceiver is mandatory.
A power supply must be distributed to each pin in
a star topology and low-ESR capacitors must be
placed at each pin for proper decoupling noise.
Decoupling each power pin is a tedious task,
especially when the noise is affecting the perfor-
mance of the transceiver in a specific bandwidth.
Usually, low value caps (15-27 pF) combined with
large value caps (100 nF) will cover a large
spectrum of frequency.
Passive components (inductors) must be in the
high-frequency category and the SRF (Self-
Resonant Frequency) should be at least two
times higher than the operating frequency.
Figure A-10 and Figure A-11 illustrate the ground and
power plane for the RF board.
Dielectric
ε
= 4.5, Thickness = 7 mils
Signal Layout, Thickness = 1.8 mils
RF Ground, Thickness = 1.2 mils
Dielectric
ε
= 4.5, Thickness = 19 mils
Power Line Routing, Thickness = 1.2 mils
Dielectric
ε
= 4.5, Thickness = 7 mils
Ground, Thickness = 1.8 mils
Note:
Care should be taken with all ground lines to prevent breakage.
相關PDF資料
PDF描述
MRSM75 Rotation detection MR sensor
MRUS51S Micro power Built-in IC ultra-minimum MR sensor
MS-012AA SOIC: 8−LEAD (POWER ICS ONLY)
MS1022 PNP RF Amplifier Transistor Surface Mount
MS1022-CT1 PNP RF Amplifier Transistor Surface Mount
相關代理商/技術參數
參數描述
MRF24J40MA 制造商:Microchip Technology Inc 功能描述:WIRELESS TRANCEIVER MODULE, Supply Voltage Min:2.4V, Supply Voltage Max:3.6V, MS
MRF24J40MA-I/RM 功能描述:Zigbee/802.15.4模塊 2.4GHz IEEE 802.15.4 Transceiver Module RoHS:否 制造商:Digi International 頻帶:902 MHz to 928 MHz 視線范圍: 數據速率: 靈敏度: 工作電源電壓:2.4 V to 3.6 V 傳輸供電電流:215 mA 接收供電電流:26 mA 輸出功率:250 mW 天線連接器類型:Wire 最大工作溫度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
MRF24J40MAT-I/RM 功能描述:射頻接收器 2.4GHz IEEE 802.15.4 Transceiver Module RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel
MRF24J40MB-I 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:IEEE 802.15.4a?￠ 2.4 GHz RF Transceiver
MRF24J40MB-I/RM 功能描述:Zigbee/802.15.4模塊 2.4GHz, 802.15.4 Xcvr w/int PA RoHS:否 制造商:Digi International 頻帶:902 MHz to 928 MHz 視線范圍: 數據速率: 靈敏度: 工作電源電壓:2.4 V to 3.6 V 傳輸供電電流:215 mA 接收供電電流:26 mA 輸出功率:250 mW 天線連接器類型:Wire 最大工作溫度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*