- 您現在的位置：買賣IC網 > PDF目錄45378 > MR80C32-25/883R (TEMIC SEMICONDUCTORS) 8-BIT, 25 MHz, MICROCONTROLLER, CQCC44 PDF資料下載
參數資料
| 型號： | MR80C32-25/883R |
| 廠商： | TEMIC SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 25 MHz, MICROCONTROLLER, CQCC44 |
| 文件頁數： | 137/182頁 |
| 文件大?。?/td> | 2994K |
| 代理商： | MR80C32-25/883R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁當前第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁
58
1477K–AVR–08/10
ATtiny26(L)
Interrupt Handling The ATtiny26(L) has two 8-bit Interrupt Mask Control Registers; GIMSK – General Interrupt
Mask Register and TIMSK – Timer/Counter Interrupt Mask Register.
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared (zero) and all interrupts are
disabled. The user software can set (one) the I-bit to enable nested interrupts. The I-bit is set
(one) when a Return from Interrupt instruction – RETI – is executed.
When the Program Counter is vectored to the actual Interrupt Vector in order to execute the
interrupt handling routine, hardware clears the corresponding flag that generated the interrupt.
Some of the interrupt flags can also be cleared by writing a logic one to the flag bit position(s) to
be cleared.
If an interrupt condition occurs when the corresponding interrupt enable bit is cleared (zero), the
interrupt flag will be set and remembered until the interrupt is enabled, or the flag is cleared by
software.
If one or more interrupt conditions occur when the Global Interrupt Enable bit is cleared (zero),
the corresponding interrupt flag(s) will be set and remembered until the Global Interrupt Enable
bit is set (one), and will be executed by order of priority.
Note that external level interrupt does not have a flag, and will only be remembered for as long
as the interrupt condition is active.
Note that the Status Register is not automatically stored when entering an interrupt routine and
restored when returning from an interrupt routine. This must be handled by software.
Interrupt Response
Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles mini-
mum. After the four clock cycles the program vector address for the actual interrupt handling
routine is executed. During this four clock cycle period, the Program Counter (10 bits) is pushed
onto the Stack. The vector is a relative jump to the interrupt routine, and this jump takes two
clock cycles. If an interrupt occurs during execution of a multi-cycle instruction, this instruction is
completed before the interrupt is served.
A return from an interrupt handling routine takes four clock cycles. During these four clock
cycles, the Program Counter (10 bits) is popped back from the Stack. When AVR exits from an
interrupt, it will always return to the main program and execute one more instruction before any
pending interrupt is served. Note that the Status Register – SREG – is not handled by the AVR
hardware, neither for interrupts nor for subroutines. For the routines requiring a storage of the
SREG, this must be performed by user software.
General Interrupt
Mask Register –
GIMSK
Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny26(L) and always reads as zero.
Bit 6 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-
nal pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the MCU
general Control Register (MCUCR) define whether the external interrupt is activated on rising or
falling edge, on pin change, or low level of the INT0 pin. Activity on the pin will cause an interrupt
request even if INT0 is configured as an output. The corresponding interrupt of External Interrupt
Request 0 is executed from program memory address $001. See also “External Interrupt” on
Bit
765
4321
0
$3B ($5B)
–
INT0
PCIE1
PCIE0
–
GIMSK
Read/Write
R
R/W
R
Initial Value
000
0000
0
相關PDF資料 |
PDF描述 |
|---|---|
| MR80C52CXXX-12SBR | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44 |
| MR80C32-16SC | 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44 |
| MD80C32-30SCD | 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 |
| MR83C154TXXX-20P883R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44 |
| MQ80C52XXX-25SBR | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MR80C32-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MR80C32-36 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MR80C51BH | 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space |
| MR80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MR80C86/B | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述:Microprocessor, 16 Bit, 44 Pin, Ceramic, LCC |
發布緊急采購，3分鐘左右您將得到回復。