參數資料
型號: MPC7410HX500LE
廠商: Freescale Semiconductor
文件頁數: 37/56頁
文件大?。?/td> 0K
描述: IC MPU 32BIT 500MHZ 360-CBGA
標準包裝: 44
系列: MPC74xx
處理器類型: 32-位 MPC74xx PowerPC
速度: 500MHz
電壓: 1.8V
安裝類型: 表面貼裝
封裝/外殼: 360-BBGA,F(xiàn)CCBGA
供應商設備封裝: 360-FCCBGA(25x25)
包裝: 托盤
MPC7410 RISC Microprocessor Hardware Specifications, Rev. 6.1
42
Freescale Semiconductor
System Design Information
The COP interface has a standard header for connection to the target system, based on the 0.025" square-post 0.100"
centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a connector
key.
There is no standardized way to number the COP header shown in Figure 25; consequently, many different pin
numbers have been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while
others use left-to-right then top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with
an IC). Regardless of the numbering, the signal placement recommended in Figure 25 is common to all known
emulators.
The QACK signal shown in Figure 25 is usually connected to the PCI bridge chip in a system and is an input to the
MPC7410 informing it that it can go into the quiescent state. Under normal operation this occurs during a low-power
mode selection. In order for COP to work, the MPC7410 must see this signal asserted (pulled down). While shown
on the COP header, not all emulator products drive this signal. If the product does not, a pull-down resistor can be
populated to assert this signal. Additionally, some emulator products implement open-drain type outputs and can
only drive QACK asserted; for these tools, a pull-up resistor can be implemented to ensure this signal is negated
when it is not being driven by the tool. Note that the pull-up and pull-down resistors on the QACK signal are
mutually exclusive and it is never necessary to populate both in a system. To preserve correct power-down operation,
QACK should be merged via logic so that it also can be driven by the PCI bridge.
8.8 Thermal Management Information
This section provides thermal management information for the MPC7410 for air-cooled applications. Proper
thermal control design is primarily dependent on the system-level design—the heat sink, airflow, and thermal
interface material. To reduce the die-junction temperature, heat sinks may be attached to the package by several
methods such as spring clip to holes in the printed circuit board or with screws and springs to the printed circuit
board; see Figure 26 for the BGA package and Figure 27 for the LGA package. This spring force should not exceed
5.5 pounds of force. Note that care should be taken to avoid focused forces being applied to die corners and/or edges
when mounting heat sinks.
Figure 26. BGA Package Exploded Cross-Sectional View with Heat Sink Clip to PCB Option
Thermal Interface Material
Heat Sink
BGA Package
Heat Sink
Clip
Printed-Circuit Board
相關PDF資料
PDF描述
ABB108DHAD CONN EDGECARD 216PS R/A .050 SLD
MC7410VU500LE IC MPU RISC 32BIT 360-FCCBGA
ACB108DHAN CONN EDGECARD 216PS R/A .050 DIP
IDT70V9369L9PF8 IC SRAM 288KBIT 9NS 100TQFP
MPC7410VS500LE IC MPU PPC 500MHZ 360-FCCLGA
相關代理商/技術參數
參數描述
MPC7410HX500LE 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 500MHZ 360-FCCBGA
MPC7410RX400LE 功能描述:微處理器 - MPU REV 1.4 1.8+/-.05V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC7410RX400NE 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC7410 RISC Microprocessor Hardware Specifications Addendum
MPC7410RX450NE 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC7410 RISC Microprocessor Hardware Specifications Addendum
MPC7410RX500LE 功能描述:IC MPU 32BIT 500MHZ PPC 360-CBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC74xx 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA(25x25) 包裝:托盤