R
參數資料
型號: MPC7410HX400LE
廠商: Freescale Semiconductor
文件頁數: 33/56頁
文件大?。?/td> 0K
描述: IC MPU 32BIT LP HP 360-CBGA
標準包裝: 44
系列: MPC74xx
處理器類型: 32-位 MPC74xx PowerPC
速度: 400MHz
電壓: 1.8V
安裝類型: 表面貼裝
封裝/外殼: 360-BBGA,F(xiàn)CCBGA
供應商設備封裝: 360-FCCBGA(25x25)
包裝: 托盤
MPC7410 RISC Microprocessor Hardware Specifications, Rev. 6.1
Freescale Semiconductor
39
System Design Information
RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. Figure 24 describes the alternate
driver impedance measurement circuit.
Figure 24. Alternate Driver Impedance Measurement Circuit
Table 15 summarizes the signal impedance results. The driver impedance values were characterized at 0°, 65°, and
105°C. The impedance increases with junction temperature and is relatively unaffected by bus voltage.
8.6 Pull-Up Resistor Requirements
The MPC7410 requires pull-up resistors (1 k
Ω–5 kΩ) on several control pins of the bus interface to maintain the
control signals in the negated state after they have been actively negated and released by the MPC7410 or other bus
masters. These pins are: TS, ARTRY, SHDO, SHD1.
Four test pins also require pull-up resistors (100
Ω1kΩ). These pins are CHK, L1_TSTCLK, L2_TSTCLK, and
LSSD_MODE. These signals are for factory use only and must be pulled up to OVDD for normal machine
operation.
If pull-down resistors are used to configure BVSEL or L2VSEL, the resistors should be less than 250
Ω (see Table
12). Because PLL_CFG[0:3] must remain stable during normal operation, strong pull-up and pull-down resistors
(1 k
Ω or less) are recommended to configure these signals in order to protect against erroneous switching due to
ground bounce, power supply noise or noise coupling.
In addition, CKSTP_OUT is an open-drain style output that requires a pull-up resistor (1 k
Ω–5 kΩ) if it is used by
the system. The CKSTP_IN signal should likewise be pulled up through a pull-up resistor (1 k
Ω–5 kΩ) to prevent
erroneous assertions of this signal.
During inactive periods on the bus, the address and transfer attributes may not be driven by any master and may,
therefore, float in the high-impedance state for relatively long periods of time. Since the MPC7410 must continually
monitor these signals for snooping, this float condition may cause excessive power draw by the input receivers on
Table 15. Impedance Characteristics
VDD = 1.8 V, OVDD = 2.5 V, Tj = 0° – 105°C
Impedance
Processor Bus
L2 Bus
Symbol
Unit
RN
41.5–54.3
42.7–54.1
Z0
Ω
RP
37.3–55.3
39.3–50.0
Z0
Ω
(L2)OVDD
BGA
Data
Pin
Vforce
OGND
相關PDF資料
PDF描述
AMM43DSAN CONN EDGECARD 86POS R/A .156 SLD
XC4052XL-2BG432I IC FPGA I-TEMP 3.3V 2SPD 432MBGA
XC4052XL-2BG432C IC FPGA C-TEMP 3.3V 2SPD 432MBGA
AMM43DSAH CONN EDGECARD 86POS R/A .156 SLD
FMC25DRES-S93 CONN EDGECARD 50POS .100 EYELET
相關代理商/技術參數
參數描述
MPC7410HX400NE 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC7410 RISC Microprocessor Hardware Specifications Addendum
MPC7410HX450LE 功能描述:微處理器 - MPU NT HITCE RV1.4 1.8V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC7410HX450NE 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC7410 RISC Microprocessor Hardware Specifications Addendum
MPC7410HX500LE 功能描述:微處理器 - MPU NT HITCE RV1.4 1.8V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC7410HX500LE 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 500MHZ 360-FCCBGA