- 您現在的位置：買賣IC網 > PDF目錄371126 > MMFT5P03HD (ON SEMICONDUCTOR) 30V N-Channel PowerTrench MOSFET PDF資料下載
參數資料
| 型號： | MMFT5P03HD |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 功率晶體管 |
| 英文描述： | 30V N-Channel PowerTrench MOSFET |
| 中文描述： | 3.7 A, 30 V, 0.1 ohm, P-CHANNEL, Si, POWER, MOSFET, TO-261AA |
| 封裝： | CASE 318E-04, 4 PIN |
| 文件頁數： | 10/12頁 |
| 文件大小： | 198K |
| 代理商： | MMFT5P03HD |
10
Motorola TMOS Power MOSFET Transistor Device Data
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones and a figure
for belt speed. Taken together, these control settings make up
a heating “profile” for that particular circuit board. On
machines controlled by a computer, the computer remembers
these profiles from one operating session to the next. Figure
16 shows a typical heating profile for use when soldering a
surface mount device to a printed circuit board. This profile will
vary among soldering systems, but it is a good starting point.
Factors that can affect the profile include the type of soldering
system in use, density and types of components on the board,
type of solder used, and the type of board or substrate material
being used. This profile shows temperature versus time. The
line on the graph shows the actual temperature that might be
experienced on the surface of a test board at or near a central
solder joint. The two profiles are based on a high density and
a low density board. The Vitronics SMD310 convection/in-
frared reflow soldering system was used to generate this
profile. The type of solder used was 62/36/2 Tin Lead Silver
with a melting point between 177–189
°
C. When this type of
furnace is used for solder reflow work, the circuit boards and
solder joints tend to heat first. The components on the board
are then heated by conduction. The circuit board, because it
has a large surface area, absorbs the thermal energy more
efficiently, then distributes this energy to the components.
Because of this effect, the main body of a component may be
up to 30 degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
170
°
C
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
Figure 16. Typical Solder Heating Profile
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
相關PDF資料 |
PDF描述 |
|---|---|
| MMFT5P03HDT3 | 30V N-Channel PowerTrench MOSFET |
| MMFT5P03HD | TMOS MEDIUM POWER FET 5.2 AMPERES 30 VOLTS |
| MMG05N60D | POWERLUX IGBT |
| MMG05N60D | Insulated Gate Bipolar Transistor |
| MMPQ2222 | Quad General Purpose Transistors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MMFT5P03HDT1 | 功能描述:MOSFET P-CH 30V 3.7A SOT223 RoHS:否 類別:分離式半導體產品 >> FET - 單 系列:- 標準包裝:1,000 系列:MESH OVERLAY™ FET 型:MOSFET N 通道，金屬氧化物 FET 特點:邏輯電平門 漏極至源極電壓(Vdss):200V 電流 - 連續漏極(Id) @ 25° C:18A 開態Rds（最大）@ Id, Vgs @ 25° C:180 毫歐 @ 9A，10V Id 時的 Vgs(th)（最大）:4V @ 250µA 閘電荷(Qg) @ Vgs:72nC @ 10V 輸入電容 (Ciss) @ Vds:1560pF @ 25V 功率 - 最大:40W 安裝類型:通孔 封裝/外殼:TO-220-3 整包 供應商設備封裝:TO-220FP 包裝:管件 |
| MMFT5P03HDT3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:TMOS P-CHANNEL FIELD FEECT TRANSISTOR |
| MMFT6N03HD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:TMOS POWER 6.0 AMPERES 30 VOLTS |
| MMFT960T1 | 功能描述:MOSFET 60V 300mA N-Channel RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| MMFT960T1_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power MOSFET 300 mA, 60 Volts N−Channel SOT−223 |
發布緊急采購，3分鐘左右您將得到回復。