參數資料
型號： MLX90308LDF-DAA-000-TU
廠商： Melexis Technologies NV
文件頁數： 6/28頁
文件大?。?/td> 0K
描述： IC SENSOR PROG INTERFACE 16-SOIC
標準包裝： 46
類型： 傳感器接口
輸入類型： 電壓
輸出類型： 電壓
接口： UART
電流 - 電源： 5mA
安裝類型： 表面貼裝
封裝/外殼： 16-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 16-SOIC W
包裝： 管件
產品目錄頁面： 1460 (CN2011-ZH PDF)
配用： EVB90308-ND - DEMO KIT MLX90308 SENS INTERFACE
其它名稱： MLX90308CCC
MLX90308D-LDF
MLX90308LDF
MLX90308LDF-DA
MLX90308LDF-DA-ND
MLX90308LDF-ND
3901090308
Rev 007
Page 14
May/12
MLX90308
Programmable Sensor Interface
Selected input
MUX Value
TPO
0010
IAO
0110
GNO
0000
VMO
0011
Level Steering
The level steering option allows configuration of the IO
pins as outputs to indicate the relative level of a
selected signal. See Figure 7. The levels at which the
two outputs change state are programmed by the
user. The programmed levels are set as eight bit
numbers and compared to the upper eight bits of the
digitized signal. This function utilizes the same
resources as the alarm function. The two functions
(level
steering
and
alarm)
can
not
be
used
simultaneously. Four bytes in the EEPROM command
this option. The first byte is used to select the input,
while the last three comprise the transition levels. The
control byte for the level steering is the same as for
the alarm. The four MSB’s hold the code for the
selected
input.
The
control
byte
has
several
possibilities as designated by the MUX settings (See
Table 8)
Communications
The MLX90308 firmware transfers a complete byte of
data into and from the memory based on a simple
command structure. The commands allow data to be
read and written to and from the EEPROM and read
from the RAM. RAM data that can be read includes
the current digitized temperature and digitized GNO.
The commands are described below. Melexis provides
setup software for programming the MLX90308.
Table 8. Level Steering Bit Definitions
Table 9. Mode Byte Bit Definition
Bit
Function
Remarks
7
1= EEPROM Checksum test active
0= EEPROM Checksum test inactive
EEPROM Checksum test. Checksum test failure will
force the output to the value programmed in bytes 40
and 41 of the EEPROM (See Table 10).
6
0 = Analog Mode
1 = Digital Mode
Digital mode must be activated when VMO and CMO
both active.
5
0 = Alarm function inactive
1 = Alarm function active
Alarm functions are like “l(fā)imiting functions”:
If defined ADC INPUT is below low alarm trigger,
then DIGMOD becomes active with alarm low
output).
If defined ADC INPUT is above high alarm trigger,
then DIGMOD becomes active with alarm high
output.
Note: Deactivated if the level steering mode is active
4
0 = IO1/IO2 are not active outputs
1 = level steering: IO1/IO2 are active
outputs
Depending on the sampled input, IO1/IO2 will be a
two bit digital output. If IO1/IO2 are not active outputs,
then they will be analog inputs.
3
0 = Turbo inactive
1 = Turbo active
2
0 = VMO inactive
1 = VMO active
1
0 = Internal temperature sensor active
1 = External temperature sensor
active
0
0 = CMO inactive
1 = CMO active
CMO has fixed digital value (EEPROM byte - see
below) if both VMO and CMO are active. To activate
this value, the digital mode must be activated.
相關PDF資料
PDF描述
MLX90314LDF-BAA-000-TU IC SENSOR PROG HIGH GAIN 16-SOIC
MM908E621ACDWBR2 IC SW QUAD HB/TRPL HISID 54-SOIC
MM908E622ACEK IC HALF-BRIDGE QUAD 54-SOIC
MM908E624ACEWR2 IC SWITCH TRPL HI MCU/LIN 54SOIC
MM908E625ACDWB IC QUAD HALF BRDG MCU/LIN 54SOIC
相關代理商/技術參數
參數描述
MLX90308LUF 制造商:MELEXIS 制造商全稱:Melexis Microelectronic Systems 功能描述:Programmable Sensor Interface
MLX90313 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface
MLX90313KDF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface
MLX90314 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface
MLX90314AB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*