- 您現在的位置：買賣IC網 > PDF目錄1954 > MLX90308LDF-DAA-000-TU (Melexis Technologies NV)IC SENSOR PROG INTERFACE 16-SOIC PDF資料下載
參數資料
| 型號： | MLX90308LDF-DAA-000-TU |
| 廠商： | Melexis Technologies NV |
| 文件頁數： | 2/28頁 |
| 文件大小： | 0K |
| 描述： | IC SENSOR PROG INTERFACE 16-SOIC |
| 標準包裝： | 46 |
| 類型： | 傳感器接口 |
| 輸入類型： | 電壓 |
| 輸出類型： | 電壓 |
| 接口： | UART |
| 電流 - 電源： | 5mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 管件 |
| 產品目錄頁面： | 1460 (CN2011-ZH PDF) |
| 配用： | EVB90308-ND - DEMO KIT MLX90308 SENS INTERFACE |
| 其它名稱： | MLX90308CCC MLX90308D-LDF MLX90308LDF MLX90308LDF-DA MLX90308LDF-DA-ND MLX90308LDF-ND |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MLX90308
Programmable Sensor Interface
3901090308
Rev 007
Page 10
May/12
Digital Features
Microprocessor, LX11 Core, Interrupt
Controller, Memories
The LX11 microcontroller core is described in its own
datasheet. As an overview, this implementation of the
LX11 RISC core has following resources:
Two accumulators, one index and two interrupt
accumulators.
15 - 8 bit I/O ports to internal resources.
64 byte RAM.
4 kbytes ROM : 3 kbytes is available for the
customer's application firmware. 1k is
reserved for test.
48 x 8 bit EEPROM.
Four interrupt sources, two UART interrupts
and two timers.
UART
The serial link is a potentially full-duplex UART. It is
receive-buffered, in that it can receive a second byte
before a previously received byte has been read from
the receiving register. However, if the first byte is not
read by the time the reception of the second byte is
completed, the first byte will be lost. The UART's baud
rate depends on the RC-oscillator's frequency and the
"TURBO"-bit
(see
output
port).
Transmitted
and
received data has the following structure: start bit = 0,
8 bits of data, stop bit = 1.
Sending Data
Writing a byte to port 1 automatically starts a
transmission sequence. The TX Interrupt is set when
the STOP-bit of the byte is latched on the serial line.
Receiving Data
Reception is initialized by a 1 to 0 transition on the
serial line (i.e., a START-bit). The baud rate period
(i.e., the duration of one bit) is divided into 16 phases.
The first six and last seven phases of a bit are not
used. The decision on the bit-value is then the result of
a majority vote of phase 7, 8 and 9 (i.e., the center of
the bit).
Spike synchronization is avoided by de-bouncing on
the incoming data and a verification of the START-bit
value. The RX Interrupt is set when the stop bit is
latched in the UART.
Timer
The clock of the timers TMI and TPI is taken directly
from the main oscillator. The timers are never
reloaded, so the next interrupt will take place 2x
oscillator pulses after the first interrupt.
Watch Dog
An internal watch dog will reset the whole circuit in
case of a software crash. If the watch dog counter is
not reset at least once every 26 milliseconds (@ 2.46
MHz main clock), the microcontroller and all the
peripherals will be reset.
Firmware
The
MLX90308
firmware
performs
the
signal
conditioning by either of two means: analog or digital.
The analog signal conditioning allows separate offset
and gain temperature coefficients for up to four
temperature ranges. Digital mode allows for all of the
analog capabilities plus up to five different gain values
based on the input signal level. Also available in both
modes is the capability of range limiting and level
steering.
.
Temperature Processing
In both analog and digital modes, the temperature
reading controls the temperature compensation. This
temperature reading is filtered as designated by the
user. The filter adjusts the temperature reading by
factoring in a portion of the previous value. This helps
to minimize the effect of noise when using an external
temperature sensor. The filter equation is:
If measured_temp > Temp_f(n) then
Temp_f(n+1) = Temp_f(n) + [measured_temp -
Temp_f(n)] / [2
n_factor].
If measured_temp < Temp_f(n), then
Temp_f(n+1) = Temp_f(n) - [measured_temp -
Temp_f(n)] [2
n_factor].
Temp_f(n+1) = new filtered temperature value.
Temp_f(n) = previous filtered temperature value.
Measured_temp = Value from temperature A to D.
N_factor = Filter value set by the user (four
LSB’s of byte 25 of EEPROM), range 0-6.
The filtered temperature value, Temp_f, is stored in
RAM bytes 58 and 59. The data is a 10 bit value, left
justified in a 16 bit field.
相關PDF資料 |
PDF描述 |
|---|---|
| MLX90314LDF-BAA-000-TU | IC SENSOR PROG HIGH GAIN 16-SOIC |
| MM908E621ACDWBR2 | IC SW QUAD HB/TRPL HISID 54-SOIC |
| MM908E622ACEK | IC HALF-BRIDGE QUAD 54-SOIC |
| MM908E624ACEWR2 | IC SWITCH TRPL HI MCU/LIN 54SOIC |
| MM908E625ACDWB | IC QUAD HALF BRDG MCU/LIN 54SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MLX90308LUF | 制造商:MELEXIS 制造商全稱:Melexis Microelectronic Systems 功能描述:Programmable Sensor Interface |
| MLX90313 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface |
| MLX90313KDF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface |
| MLX90314 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface |
| MLX90314AB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface |
發布緊急采購，3分鐘左右您將得到回復。