Supply voltage (ratiometric) VDD
參數資料
型號: MLX90308LDF-DAA-000-TU
廠商: Melexis Technologies NV
文件頁數: 26/28頁
文件大?。?/td> 0K
描述: IC SENSOR PROG INTERFACE 16-SOIC
標準包裝: 46
類型: 傳感器接口
輸入類型: 電壓
輸出類型: 電壓
接口: UART
電流 - 電源: 5mA
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 16-SOIC W
包裝: 管件
產品目錄頁面: 1460 (CN2011-ZH PDF)
配用: EVB90308-ND - DEMO KIT MLX90308 SENS INTERFACE
其它名稱: MLX90308CCC
MLX90308D-LDF
MLX90308LDF
MLX90308LDF-DA
MLX90308LDF-DA-ND
MLX90308LDF-ND
MLX90308
Programmable Sensor Interface
3901090308
Rev 007
Page 7
May/12
Supply voltage (ratiometric) VDD Max
6V
Supply voltage (ratiometric) VDD Min
4.5V
Supply voltage (operating), VDD1 Max
35V
Reverse voltage protection
-0.7V
Supply current, Current Mode, IDD
3.5mA
Supply current, Voltage Mode, IDD
4.5mA
Output current, IVMO
8mA
Output current (short to VDD), ISCVMO
100mA
Output current (short to VSS), ISCVMO
8mA
Output voltage, VVMO
+11V
Power dissipation, PD
71mW
Operating temperature range, TA
-40 to +140°
Storage temperature range, TS
-55 to +150°
Maximum junction temperature, TJ
150°C
Unique Features
Customization
Melexis
can
customize
the
MLX90308
in
both
hardware and firmware for unique requirements. The
hardware design provides 64 bytes of RAM, 3 kbytes
of ROM, and 48 bytes of EEPROM for use by the
firmware.
Special Information
The output of the sensor bridge is amplified via offset
and gain amplifiers and then converted to the correct
output signal form in one of the output stages.
The sensitivity and offset of the analog signal chain
are defined by numbers passed to the DAC interfaces
from the microcontroller core (GN[9:0] and OF[9:0]).
The
wide
range
of
bridge
offset
and
gain
is
accommodated by means of a 2-bit coarse adjustment
DAC in the offset adjustment (CSOF[1:0]), and a
similar one in the gain adjustment (CSGN[2:0]). The
signal path can be directed through the processor for
digital processing. Two I/O pins are available for
analog inputs or digital outputs. These pins can be
used for alarms on various points on the analog signal
path and built-in or external temperature values.
Programming and Setup
The MLX90308 needs to have the compensation
coefficients programmed for a particular bridge
sensor
to
create
the
sensor
system.
Programming
the
EEPROM
involves
some
minimal
communications
interface
circuitry,
Melexis’
setup
software,
and
a
PC.
The
communications interface circuitry is available in
a
de ve lopm ent
b oar d.
T his
circuitr y
communicates with the PC via a standard RS-
232 serial communications port.
Cross Reference
There are no known devices which the MLX 90308
can replace.
ESD Precautions
Observe standard ESD control procedures for CMOS
semiconductors.
Table 2. Absolute Maximum Ratings
相關PDF資料
PDF描述
MLX90314LDF-BAA-000-TU IC SENSOR PROG HIGH GAIN 16-SOIC
MM908E621ACDWBR2 IC SW QUAD HB/TRPL HISID 54-SOIC
MM908E622ACEK IC HALF-BRIDGE QUAD 54-SOIC
MM908E624ACEWR2 IC SWITCH TRPL HI MCU/LIN 54SOIC
MM908E625ACDWB IC QUAD HALF BRDG MCU/LIN 54SOIC
相關代理商/技術參數
參數描述
MLX90308LUF 制造商:MELEXIS 制造商全稱:Melexis Microelectronic Systems 功能描述:Programmable Sensor Interface
MLX90313 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface
MLX90313KDF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable IR Sensor Interface
MLX90314 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface
MLX90314AB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Sensor Interface