- 您現在的位置：買賣IC網 > PDF目錄1954 > MCZ33993EWR2 (Freescale Semiconductor)IC MULTIPLE SWITCH DETECT 32SOIC PDF資料下載
參數資料
| 型號： | MCZ33993EWR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 14/28頁 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLE SWITCH DETECT 32SOIC |
| 標準包裝： | 1,000 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 32-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 32-SOIC |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33993
TYPICAL APPLICATIONS
INTRODUCTION
ARCHIVE
INFORMATION
ARCHIVE
INFORMATION
Figure 13. Analog Ratiometric Conversion
To read a potentiometer sensor, the wiper should be
grounded and brought back to the module ground, as
illustrated in Figure 13. With the wiper changing the
impedance of the sensor, the analog voltage on the input will
represent the position of the sensor.
Using the Analog feature to provide 2.0 mA of pull-up
current to an analog sensor may induce error due to the
accuracy of the current source. For this reason, a ratiometric
conversion must be considered. Using two current sources
(one for the sensor and one to set the reference voltage to the
A/D converter) will yield a maximum error (owing to the
33993) of 4%.
Higher accuracy may be achieved through module level
calibration. In this example, we use the resistor values from
Figure 13 and assume the current sources are 4% from each
other. The user may use the module end-of-line tester to
calculate the error in the A/D conversion. By placing a
2.0 k
Ω, 0.1% resistor in the end-of-line test equipment and
assuming a perfect 2.0 mA current source from the 33993, a
calculated A/D
conversion may be obtained. Using the equation yields the
following:
The ADC value of 213 counts is the value with 0% error
(neglecting the resistor tolerance and AMUX input offset
voltage). Now we can calculate the count value induced by
the mismatch in current sources. From a sample device the
maximum current source was measured at 2.05 mA and
minimum current source was measured at 1.99 mA. This
yields 3% error in A/D conversion. The A/D measurement
will be as follows:
This A/D conversion is 3% low in value. The error
correction factor of 1.03 may be used to correct the value:
An error correction factor may then be stored in E2
memory and used in the A/D calculation for the specific input.
Each input used as analog measurement will have a
dedicated calibrated error correction factor.
POWER MOSFET/LED DRIVER AND MONITOR
Because of the flexible programming of the 33993 device,
it may be used to drive small loads like LEDs or MOSFET
gates. It was specifically designed to power up in the Normal
mode with the inputs tri-state. This was done to ensure the
LEDs or MOSFETs connected to the 33993 power up in the
off-state. The Switch Programmable (SP0–SP7) inputs have
a source-and-sink capability, providing effective MOSFET
gate control. To complete the circuit, a pull-down resistor
should be used to keep the gate from floating during the
where the SG0 input is used to monitor the drain-to-source
voltage of the external MOSFET. The 1.5 k
Ω resistor is used
to set the drain-to-source trip voltage. With the 2.0 mA
current source enabled, an interrupt will be generated when
the drain-to-source voltage is approximately 1.0 V.
VDD
VPWR
VDD
SI
SO
SCLK
INT
CS
AMUX
MOSI
MISO
AN0
VBAT
SP0
SP1
SP7
SG1
SG0
SG12
SG13
WAKE
VBAT
SCLK
CS
INT
16
2.0
VPWR
2.0 mA
2.39 k
Ω
0.1%
4.54 V to 5.02 V
Analog
Ports
VREF(H)
VREF(L)
Analog Sensor
or Analog Switch
R2
I2
I1
R1
VPWR
mA
2.0
VPWR
mA
16
mA
33993
MCU
ADC =
I1 x R1
I2 x R2
x225
ADC =
2.0 mA x 2.0 k
Ω
x 225
2.0 mA x 2.39 k
Ω
ADC = 213 counts
ADC =
1.99 mA x 2.0 k
Ω
x225
2.05 mA x 2.39 k
Ω
ADC = 207 counts
ADC = 207 counts x 1.03
ADC = 213 counts
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ79076EGR2 | IC IGNITION CTRL ELECTR 16-SOIC |
| MIC2070-2PCQS TR | IC USB PWR CTRLR DUAL 16-QSOP |
| MIC2550ABTS TR | IC USB TRANSCEIVER 14-TSSOP |
| MIC2550YTS | IC USB TRANSCEIVER 14-TSSOP |
| MIC2551ABML TR | IC USB TRANSCEIVER 16-MLF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33996CEK | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Bulk |
| MCZ33996CEKR2 | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Tape and Reel |
| MCZ33996EK | 功能描述:開關變換器、穩壓器與控制器 16 LOW SIDE SW RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MCZ33996EK | 制造商:Freescale Semiconductor 功能描述:IC LOAD SWITCH 27V 32SOIC |
| MCZ33996EKR2 | 功能描述:開關變換器、穩壓器與控制器 16 LOW SIDE SW 1.20HM RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。