- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33880EG (飛思卡爾半導體(中國)有限公司) Configurable Octal Serial Switch with Serial Peripheral Interface I/O PDF資料下載
參數資料
| 型號： | MCZ33880EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Configurable Octal Serial Switch with Serial Peripheral Interface I/O |
| 中文描述： | 配置八路系列開關串行外設接口的I / O |
| 文件頁數： | 18/25頁 |
| 文件大?。?/td> | 341K |
| 代理商： | MCZ33880EG |
Analog Integrated Circuit Device Data
Freescale Semiconductor
18
33880
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
SHORTED LOAD FAULT
A shorted load (overcurrent) fault can be caused by any
output being shorted directly to supply or an output causing
the device to current limit (linear short).
There are two safety circuits progressively in operation
during load short conditions providing system protection:
1. The device’s output current is monitored in an analog
fashion using SENSEFET
approach and current
limited.
2. The device’s output thermal limit is sensed and when
attained causes only the specific faulted output to shut
down. The output will remain off until cooled. The
device will then reassert the output automatically. The
cycle will continue until the fault is remove or the
command bit instructs the output off.
UNDERVOLTAGE SHUTDOWN
An undervoltage V
DD
condition will result in the global
shutdown of all outputs. The undervoltage threshold is
between 3.9 V and 4.6 V. When V
DD
goes below the
threshold, all outputs are turned OFF and the Fault Status
(FS) register is cleared. As V
DD
returns to normal levels, the
FS register will resume normal operation.
An undervoltage condition at the VPWR pin will not cause
output shutdown and reset. When V
PWR
is between 5.5 V
and 9.0 V, the output will operate per the command word.
However, the status as reported by the serial data output
(DO) pin may not be accurate below 9.0 V V
PWR
. Proper
operation at V
PWR
voltages below 5.5 V cannot be
guaranteed.
OUTPUT VOLTAGE CLAMP
Each output of the 33880 incorporates an internal voltage
clamp to provide fast turn-off and transient protection of each
output. Each clamp independently limits the drain-to-source
voltage to 45 V for low-side drive configurations and -20 V for
high-side drive configurations (see
Figure 25
). The total
energy clamped (E
J
) can be calculated by multiplying the
current area under the current curve (I
A
) times the clamp
voltage (V
CL
).
Characterization of the output clamps, using a single pulse
non-repetitive method at 0.3 A, indicates the maximum
energy to be 50 mJ at 150
°
C junction temperature per output.
Figure 25. Output Voltage Clamping
SPI CONFIGURATIONS
The SPI configuration on the 33880 device is consistent
with other devices in the OSS family. This device may be
used in serial SPI or parallel SPI with the 33291 and 33298.
Different SPI configurations may be provided. For more
information, contact Analog Products Division.
REVERSE BATTERY
The 33880 has been designed with reverse battery
protection on the VPWR pin. However, the device does not
protect the load from reverse battery. During the reverse
battery condition, current will flow through the load via the
output MOSFET substrate diode. Under this circumstance
relays may energize and lamps will turn on. If load reverse
battery protection is desired, a diode must be placed in series
with the load.
Area (I
A
)
Clamp Energy
(E
J
= I
A
x V
CL
)
Clamp Energy
(E
J
= I
A
x V
CL
)
Drain Voltage
Source Voltage
Time
Time
Drain-to-Source Clamp
Voltage (V
CL
= 45 V)
Drain Current
(I
D
= 0.3 A)
GND
V
BAT
GND
Drain-to-Source ON
Voltage (V
DS(ON)
)
Drain-to-Source ON
Voltage (V
DS(ON)
)
Current
Area (I
A
)
Source Current
(I
S
= 0.3 A)
Source Clamp Voltage
(V
CL
= -20 V)
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33883EG | H-Bridge Gate Driver IC |
| MCZ33884EG | Switch Monitor Interface |
| MCZ33887EK | 5.0 A H-Bridge with Load Current Feedback |
| MCZ33889BEG | System Basis Chip with Low Speed Fault Tolerant CAN Interface |
| MCZ33927EK | Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33880EGR2 | 功能描述:電源開關 IC - 配電 CONFIG OCTAL SERIAL SW RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MCZ33880EW | 功能描述:電源開關 IC - 配電 CONFIG OCTAL SER SWITCH RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MCZ33880EWR2 | 功能描述:電源開關 IC - 配電 CONFIG OCTAL SER SWITCH RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MCZ33883EG | 功能描述:功率驅動器IC FULL BRIDGE GATE DRIVER RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33883EG | 制造商:Freescale Semiconductor 功能描述:SEMICONDUCTOR |
發布緊急采購，3分鐘左右您將得到回復。