DSI COMMANDS AND RESPONSES REQUEST ID COMMA" />
參數資料
型號： MCZ33793EF
廠商： Freescale Semiconductor
文件頁數： 10/27頁
文件大?。?/td> 0K
描述： IC DSI SLAVE REMOTE SENS 16-SOIC
標準包裝： 48
類型： 傳感器接口
輸入類型： 邏輯
輸出類型： 邏輯
接口： 并聯
電流 - 電源： 250mA
安裝類型： 表面貼裝
封裝/外殼： 16-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 16-SOIC N
包裝： 管件
產品目錄頁面： 808 (CN2011-ZH PDF)
Analog Integrated Circuit Device Data
18
Freescale Semiconductor
33793
FUNCTIONAL DEVICE OPERATION
DSI COMMANDS AND RESPONSES
REQUEST ID COMMAND
This command will cause the device ID information to be read
from internal storage and returned to the master during the
response to the next message. The command format is found
REQUEST ID RESPONSE
This response message is sent during the next message
following a valid long-word Request ID command to the
addressed device. The response format is found in Table 19.
The high byte is omitted during the short-word response. No
response is generated if the command address field was $0.
CLEAR COMMAND
This command will open the bus switch and reset all registers
to the reset state. The command format is found in Table 20.
No response is generated for the Clear command.
READ/WRITE NVM COMMAND
If the NV bit has been set by a previous Initialization
command and the NVM has not been programmed
previously, this command will permanently program the
device’s one-time programmable address and return the
programmed value during the next message time. Once
programmed, this nonvolatile address is used to set the
device address register on the next and all subsequent
power-ups. If the device is not blank, this command will return
the programmed value during the next message time.
Programming the NVM address to $0 is allowed. This
ensures that the device always acts as a dynamically
addressable device and would be immune to any inadvertent
future NVM programming sequences.
Table 17. I/O Control Response Format
High Byte
Low Byte
CRC
A3
A2
A1
A0
0
L3
L2
L1
L0
DR3
DR2
DR1
DR0
X3
X2
X1
X0
Legend
A[3:0] = Address bits.
DR[3:0] = I/O enabled as outputs (1 = enabled as output).
L[3:0] = Programmed values.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
slave.
Table 18. Request ID Command Format
Data
Address
Command
CRC
–
A3
A2
A1
A0
0
1
0
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The address of the selected device. An
address value of “0000” is ignored by all devices.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
master.
Table 19. Request ID Response Format
Address
Status
Data
CRC
A3
A2
A1
A0
0
V2
V1
V0
0
1
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The slave address.
V[2:0] = Device version number. The silicon version number of the
device. For this device the device type is 00011 as indicated by the
lowest bits.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
slave.
Table 20. Clear Command Format
Data
Address
Command
CRC
–
A3
A2
A1
A0
0
1
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The address of the selected device. An
address value of “0000” clears all devices.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
master.
相關PDF資料
PDF描述
MCZ33797EKR2 IC SQUIB DRIVER 2CHAN 32-SOIC
MCZ33884EG IC MULTIPLE CONTACT MON 24-SOIC
MCZ33905BD3EK IC SBC CAN HS 3.3V 54SOIC
MCZ33972EWR2 IC SWITCH DETECTION MULT 32-SOIC
MCZ33975AEKR2 IC SWITCH DETECT MULT ENH 32SOIC
相關代理商/技術參數
參數描述
MCZ33793EFR2 功能描述:輸入/輸出控制器接口集成電路 ORION RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MCZ33797EK 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MCZ33797EKR2 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MCZ33800EK 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33800EKR2 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*