- 您現在的位置：買賣IC網 > PDF目錄383594 > MCP6S26 (Microchip Technology Inc.) 400000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | MCP6S26 |
| 廠商： | Microchip Technology Inc. |
| 元件分類： | FPGA |
| 英文描述： | 400000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | 單端，軌至軌I / O，低增益美國PGA |
| 文件頁數： | 18/43頁 |
| 文件大?。?/td> | 880K |
| 代理商： | MCP6S26 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
MCP6S21/2/6/8
DS21117A-page 18
2003 Microchip Technology Inc.
5.0
DIGITAL FUNCTIONS
The MCP6S21/2/6/8 PGAs use a standard SPI com-
patible serial interface to receive instructions from a
controller. This interface is configured to allow daisy
chaining with other SPI devices. There is an internal
POR (Power On Reset) that resets the registers under
low power conditions.
5.1
SPI Timing
Chip Select (CS) toggles low to initiate communication
with these devices. The first byte of each SI word (two
bytes long) is the instruction byte, which goes into the
Instruction Register. The Instruction Register points the
second byte to its destination. In a typical application,
CS is raised after one word (16 bits) to implement the
desired changes. Section 5.3, “Registers”, covers
applications using multiple 16-bit words. SO goes low
after CS goes high; it has a push-pull output that does
not go into a high-Z state.
The MCP6S21/2/6/8 devices operate in SPI Modes 0,0
and 1,1. In 0,0 mode, the clock idles in the low state
(Figure 5-1) and, in 1,1 mode, the clock idles in the high
state (Figure 5-2). In both modes, SI data is loaded into
the PGA on the rising edge of SCK and SO data is
clocked out on the falling edge of SCK. In 0,0 mode, the
falling edge of CS also acts as the first falling edge of
SCK (see Figure 5-1). There must be multiples of 16
clocks (SCK) while CS is low or commands will abort
(see Section 5.3, “Registers”).
FIGURE 5-1:
Serial bus sequence for the PGA; SPI 0,0 mode (see Figure 1-5).
FIGURE 5-2:
Serial bus sequence for the PGA; SPI 1,1 mode (see Figure 1-6).
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
b
CS
SCK
SI
Instruction Byte
Data Byte
b
b
b
SO
(first 16 bits out are always zeros)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
b
CS
SCK
SI
Instruction Byte
Data Byte
b
b
b
SO
(first 16 bits out are always zeros)
相關PDF資料 |
PDF描述 |
|---|---|
| MCP6S21 | Single-Ended, Rail-to-Rail I/O, Low Gain PGA |
| MCP6S22 | Single-Ended, Rail-to-Rail I/O, Low Gain PGA |
| MCP6S28 | 400000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| MCP73827 | Single Cell Lithium-Ion Charge Management Controller with Mode Indicator and Charge Current Monitor(單室鋰粒子充電器) |
| MCP73828(中文) | Single Cell Lithium-Ion Charge Management Controller with Charge Complete Indicator and Temperature Monitor(單室鋰粒子充電器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP6S26-I/P | 功能描述:特殊用途放大器 6-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| MCP6S26-I/SL | 功能描述:特殊用途放大器 6-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| MCP6S26-I/ST | 功能描述:特殊用途放大器 6-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| MCP6S26T-I/SL | 功能描述:特殊用途放大器 6-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| MCP6S26T-I/ST | 功能描述:特殊用途放大器 6-Chan. 12 MHz SPI RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。