- 您現在的位置：買賣IC網 > PDF目錄17100 > MCP355XDM-TAS (Microchip Technology)BOARD DEMO TINY APP SNSR MCP355X PDF資料下載
參數資料
| 型號： | MCP355XDM-TAS |
| 廠商： | Microchip Technology |
| 文件頁數： | 5/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO TINY APP SNSR MCP355X |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 22 |
| 數據接口： | 串行 |
| 輸入范圍： | ±3 V |
| 工作溫度： | -40°C ~ 125°C |
| 已用 IC / 零件： | MCP355x |
| 已供物品： | 板，CD |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
| 相關產品： | MCP3550T-60E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC MCP3550T-60E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP MCP3550T-50E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC MCP3550T-50E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP MCP3550-60E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC MCP3550-60E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP MCP3550-50E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC MCP3550-50E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP MCP3553T-E/SN-ND - IC ADC 22BIT 2.7V 1CH SPI 8SOIC MCP3553T-E/MS-ND - IC ADC 22BIT 2.7V 1CH SPI 8MSOP 更多... |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
2009 Microchip Technology Inc.
DS21950E-page 13
MCP3550/1/3
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
3.1
Voltage Reference (VREF)
The MCP3550/1/3 devices accept single-ended
reference voltages from 0.1V to VDD. Since the
converter output noise is dominated by thermal noise,
which is independent of the reference voltage, the
output noise is not significantly improved by
diminishing the reference voltage at the VREF input pin.
A reduced voltage reference will significantly improve
the INL performance (see Figure 2-4); the INL max
error is proportional to VREF2.
3.2
Analog Inputs (VIN+, VIN-)
The MCP3550/1/3 devices accept a fully differential
analog input voltage to be connected on the VIN+ and
VIN- input pins. The differential voltage that is
converted is defined by VIN = VIN+ – VIN-. The
differential voltage range specified for ensured
accuracy is from -VREF to +VREF. However, the
converter will still output valid and usable codes with
the inputs overranged by up to 12% (see Section 5.0
“Serial Interface”) at room temperature. This
overrange is clearly specified by two overload bits in
the output code.
The absolute voltage range on these input pins extends
from VSS – 0.3V to VDD + 0.3V. Any voltage above or
below this range will create leakage currents through
the Electrostatic Discharge (ESD) diodes. This current
will increase exponentially, degrading the accuracy and
noise performance of the device. The common mode of
the analog inputs should be chosen such that both the
differential analog input range and the absolute voltage
range on each pin are within the specified operating
range
defined
in
3.3
Supply Voltage (VDD, VSS)
VDD is the power supply pin for the analog and digital
circuitry within the MCP3550/1/3. This pin requires an
appropriate bypass capacitor of 0.1 F. The voltage on
this pin should be maintained in the 2.7V to 5.5V range
for specified operation. VSS is the ground pin and the
current return path for both analog and digital circuitry
of the MCP3550/1/3. If an analog ground plane is
available, it is recommended that this device be tied to
the analog ground plane of the Printed Circuit Board
(PCB).
3.4
Serial Clock (SCK)
SCK synchronizes data communication with the
device. The device operates in both SPI mode 1,1 and
SPI mode 0,0. Data is shifted out of the device on the
falling edge of SCK. Data is latched in on the rising
edge of SCK. During CS high times, the SCK pin can
idle either high or low.
3.5
Data Output (SDO/RDY)
SDO/RDY is the output data pin for the device. Once a
conversion is complete, this pin will go active-low,
acting as a ready flag. Subsequent falling clock edges
will then place the 24-bit data word (two overflow bits
and 22 bits of data, see Section 5.0 “Serial
Interface”) on the SPI bus through the SDO pin. Data
is clocked out on the falling edge of SCK.
MCP3550/1/3
Symbol
I/O/P
Description
MSOP, SOIC
1VREF
I
Reference Voltage Analog Input Pin
2VIN+
I
Non-inverting Analog Input Pin
3VIN-
I
Inverting Analog Input Pin
4VSS
P
Ground Pin
5
SCK
I
Serial Clock Digital Input Pin
6
SDO/RDY
O
Data/Ready Digital Output Pin
7CS
I
Chip Select Digital Input Pin
8VDD
P
Positive Supply Voltage Pin
Type Identification: I = Input; O = Output; P = Power
相關PDF資料 |
PDF描述 |
|---|---|
| LGU2D271MELY | CAP ALUM 270UF 200V 20% SNAP |
| MCP3551DM-PCTL | BOARD DEMO FOR MCP3551 |
| 0210490181 | CABLE JUMPER 1.25MM .203M 12POS |
| HL02150GTTR | INDUCTOR 15NH 200MA 0402 |
| SCRH6D28-180 | INDUCTOR SMD 18UH 1.32A 10KHZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP355XDV-MS1 | 功能描述:數據轉換 IC 開發工具 MCP355X Sensor App Dev Brd RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MCP3901 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two Channel Analog Front End |
| MCP3901_10 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two-Channel Analog Front End |
| MCP3901_11 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two-Channel Analog Front End Portable Instrumentation |
| MCP3901_12 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Energy Meter Reference Design |
發布緊急采購，3分鐘左右您將得到回復。