If a rising edge of Chip Select (CS) occurs du" />
參數資料
型號： MCP355XDM-TAS
廠商： Microchip Technology
文件頁數： 16/36頁
文件大?。?/td> 0K
描述： BOARD DEMO TINY APP SNSR MCP355X
產品培訓模塊： MCP3901 Analog Front End
標準包裝： 1
ADC 的數量： 1
位數： 22
數據接口： 串行
輸入范圍： ±3 V
工作溫度： -40°C ~ 125°C
已用 IC / 零件： MCP355x
已供物品： 板，CD
產品目錄頁面： 672 (CN2011-ZH PDF)
相關產品： MCP3550T-60E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC
MCP3550T-60E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP
MCP3550T-50E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC
MCP3550T-50E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP
MCP3550-60E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC
MCP3550-60E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP
MCP3550-50E/SN-ND - IC ADC 22BIT 2.7V 1CH 8SOIC
MCP3550-50E/MS-ND - IC ADC 22BIT 2.7V 1CH 8MSOP
MCP3553T-E/SN-ND - IC ADC 22BIT 2.7V 1CH SPI 8SOIC
MCP3553T-E/MS-ND - IC ADC 22BIT 2.7V 1CH SPI 8MSOP
更多...
2009 Microchip Technology Inc.
DS21950E-page 23
MCP3550/1/3
5.3
Single Conversion Mode
If a rising edge of Chip Select (CS) occurs during tCONV,
a subsequent conversion will not take place and the
device will enter low-power Shutdown mode after
tCONV completes. This is referred to as Single
Conversion mode. This operation is demonstrated in
Figure 5-2. Note that a falling edge of CS during the
same conversion that detected a rising edge, as in
Figure 5-2, will not initiate a new conversion. The data
must be read during sleep mode, with CSN low, and will
be lost as soon as the part enters in shutdown mode
(with a rising edge of CSN). After the final data bit has
been clocked out on the 25th clock, the SDO/RDY pin
will go active-high.
5.3.1
READY FUNCTION OF SDO/RDY
PIN, SINGLE CONVERSION MODE
At every falling edge of CS during the internal
conversion, the state of the internal conversion is
latched on the SDO/RDY pin to give ready or busy
information. A High state means the device is currently
performing an internal conversion and data cannot be
clocked out. A Low state means the device has finished
its conversion and the data is ready for retrieval on the
falling edge of SCK. This operation is demonstrated in
Figure 5-4. Note that the device has been put into
Single Conversion mode with the first rising edge of
CS.
FIGURE 5-4:
RDY Functionality in Single
Conversion Mode.
5.4
Continuous Conversion Mode
If no rising edge of CS occurs during any given
conversion per Figure 5-3, a subsequent conversion
will take place and the contents of the previous conver-
sion will be overwritten. This operation is demonstrated
in Figure 5-5. Once conversion output data has started
to be clocked out, the output buffer is not refreshed until
all 24 bits have been clocked. A complete read must
occur in order to read the next conversion in this mode.
The subsequent conversion data to be read will then be
the most recent conversion. The conversion time is
fixed and cannot be shortened by the rising edge of CS.
This rising edge will place the part in Shutdown mode
and all conversion data will be lost.
The transfer of data from the SINC filter to the output
buffer is demonstrated in Figure 5-5. If the previous
conversion data is not clocked out of the device, it will
be lost and replaced by the new conversion. When the
device is in Continuous Conversion mode, the most
recent conversion data is always present at the output
register for data retrieval.
FIGURE 5-5:
Most Current Continuous
Conversion Mode Data.
If a conversion is in process, it cannot be terminated
with the rising edge of CS. SDO/RDY must first
transition to a Low state, which will indicate the end of
conversion.
Note:
The Ready state is latched on each falling
edge of CS and will not dynamically
update if CS is held low. CS must be
toggled high through low.
tCONV
CS
Int. Osc
SDO/RDY
Hi-Z
tCONV
CS
Int. Osc
SCK & SDO/RDY
A
B
C
Conversion B data is clocked
out of the device here.
相關PDF資料
PDF描述
LGU2D271MELY CAP ALUM 270UF 200V 20% SNAP
MCP3551DM-PCTL BOARD DEMO FOR MCP3551
0210490181 CABLE JUMPER 1.25MM .203M 12POS
HL02150GTTR INDUCTOR 15NH 200MA 0402
SCRH6D28-180 INDUCTOR SMD 18UH 1.32A 10KHZ
相關代理商/技術參數
參數描述
MCP355XDV-MS1 功能描述:數據轉換 IC 開發工具 MCP355X Sensor App Dev Brd RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MCP3901 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two Channel Analog Front End
MCP3901_10 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two-Channel Analog Front End
MCP3901_11 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Two-Channel Analog Front End Portable Instrumentation
MCP3901_12 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Energy Meter Reference Design
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*