The I2" />
參數資料
型號： MCP3421A0T-E/OT
廠商： Microchip Technology
文件頁數： 9/30頁
文件大小： 0K
描述： IC ADC 18BIT 3.75SPS 1CH SOT23-6
標準包裝： 1
位數： 18
采樣率（每秒）： 3.75
數據接口： I²C，串行
轉換器數目： 1
電壓電源： 單電源
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： SOT-23-6
供應商設備封裝： SOT-23-6
包裝： 標準包裝
輸入數目和類型： 2 個單端，雙極；1 個差分，單極
配用： MCP3421EV-ND - BOARD EVAL FOR MCP3421 SOT23-6
其它名稱： MCP3421A0T-E/OTDKR
2006 Microchip Technology Inc.
DS22003B-page 17
MCP3421
5.5
High-Speed (HS) Mode
The I2C specification requires that a high-speed mode
device must be ‘activated’ to operate in high-speed
mode. This is done by sending a special address byte
of 00001XXX following the START bit. The XXX bits are
unique to the High-Speed (HS) mode Master. This byte
is referred to as the High-Speed (HS) Master Mode
Code (HSMMC). The MCP3421 device does not
acknowledge this byte. However, upon receiving this
code, the MCP3421 switches on its HS mode filters
and communicates up to 3.4 MHz on SDA and SCL.
The device will switch out of the HS mode on the next
STOP condition.
For more information on the HS mode, or other I2C
modes, please refer to the Phillips I2C specification.
5.6
I2C Bus Characteristics
The I2C specification defines the following bus
protocol:
Data transfer may be initiated only when the bus
is not busy.
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition.
Accordingly, the following bus conditions have been
defined using Figure 5-6.
5.6.1
BUS NOT BUSY (A)
Both data and clock lines remain HIGH.
5.6.2
START DATA TRANSFER (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition. All
commands must be preceded by a START condition.
5.6.3
STOP DATA TRANSFER (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations can be ended with a STOP condition.
5.6.4
DATA VALID (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition.
5.6.5
ACKNOWLEDGE
The Master (microcontroller) and the slave (MCP3421)
use an acknowledge pulse as a hand shake of
communication for each byte. The ninth clock pulse of
each byte is used for the acknowledgement. The
acknowledgement is achieved by pulling-down the
SDA line “LOW” during the 9th clock pulse. The clock
pulse is always provided by the Master (microcontrol-
ler) and the acknowledgement is issued by the
receiving device of the byte (Note: The transmitting
device must release the SDA line (“HIGH”) during the
acknowledge
pulse.).
For
example,
the
slave
(MCP3421) issues the acknowledgement (bring down
the SDA line “LOW”) after the end of each receiving
byte, and the master (microcontroller) issues the
acknowledgement when it reads data from the Slave
(MCP3421).
When the MCP3421 is addressed, it generates an
acknowledge after receiving each byte successfully.
The Master device (microcontroller) must provide an
extra clock pulse (9th pulse of each byte) for the
acknowledgement from the MCP3421 (slave).
The MCP3421 (slave) pulls-down the SDA line during
the acknowledge clock pulse in such a way that the
SDA line is stable low during the high period of the
acknowledge clock pulse.
During reads, the Master (microcontroller) can
terminate the current read operation by not providing
an acknowledge bit on the last byte that has been
clocked out from the MCP3421. In this case, the
MCP3421 releases the SDA line to allow the master
(microcontroller) to generate a STOP or repeated
START condition.
FIGURE 5-6:
Data Transfer Sequence on the Serial Bus.
SCL
SDA
(A)
(B)
(D)
(A)
(C)
START
CONDITION
ADDRESS OR
ACKNOWLEDGE
VALID
DATA
ALLOWED
TO CHANGE
STOP
CONDITION
相關PDF資料
PDF描述
MCP3424T-E/ST IC ADC 18BIT 3.75SPS 4CH 14TSSOP
MCP3425A0T-E/CH IC ADC 16BIT I2C PROGBL SOT23-6
MCP3427-E/MF IC ADC 16BIT I2C PROGBL 10-DFN
MCP3550T-60E/MS IC ADC 22BIT 2.7V 1CH 8MSOP
MCP6541RT-I/OT IC COMP 1.6V PUSH-PULL SOT23-5
相關代理商/技術參數
參數描述
MCP3421A1T-E/CH 功能描述:模數轉換器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MCP3421A1T-E/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference
MCP3421A2T-E/CH 功能描述:模數轉換器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MCP3421A2T-E/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference
MCP3421A3T-E/CH 功能描述:模數轉換器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*