- 您現在的位置：買賣IC網 > PDF目錄3950 > MC8641HX1250HC (Freescale Semiconductor)IC MPU SGL E600 CORE 994FCCBGA PDF資料下載
參數資料
| 型號： | MC8641HX1250HC |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 25/130頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MPU SGL E600 CORE 994FCCBGA |
| 標準包裝： | 1 |
| 系列： | MPC86xx |
| 處理器類型： | 32-位 MPC86xx PowerPC |
| 速度： | 1.25GHz |
| 電壓： | 1.05V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 994-BCBGA，F(xiàn)CCBGA |
| 供應商設備封裝： | 994-FCCBGA（33x33） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁
MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 2
120
Freescale Semiconductor
System Design Information
Local Bus - If parity is not used, tie LDP[0:3] to ground via a 4.7 k
Ω resistor, tie LPBSE to OVDD
via a 4.7 k
Ω resistor (pull-up resistor). For systems which boot from Local Bus (GPCM)-controlled
flash, a pullup on LGPL4 is required.
SerDes - Receiver lanes configured for PCI Express are allowed to be disconnected (as would
occur when a PCI Express slot is connected but not populated). Directions for terminating the
SerDes signals is discussed in Section 20.5.1, “Guidelines for High-Speed Interface Termination.”
20.5.1
Guidelines for High-Speed Interface Termination
20.5.1.1
SerDes Interface
The high-speed SerDes interface can be disabled through the POR input cfg_io_ports[0:3] and through the
DEVDISR register in software. If a SerDes port is disabled through the POR input the user can not enable
it through the DEVDISR register in software. However, if a SerDes port is enabled through the POR input
the user can disable it through the DEVDISR register in software. Disabling a SerDes port through
software should be done on a temporary basis. Power is always required for the SerDes interface, even if
the port is disabled through either mechanism. Table 72 describes the possible enabled/disabled scenarios
for a SerDes port. The termination recommendations must be followed for each port.
If the high-speed SerDes port requires complete or partial termination, the unused pins should be
terminated as described in this section.
The following pins must be left unconnected (floating):
SDn_TX[7:0]
Table 72. SerDes Port Enabled/Disabled Configurations
Disabled through POR input
Enabled through POR input
Enabled through DEVDISR
SerDes port is disabled (and cannot be
enabled through DEVDISR)
Complete termination required
(Reference Clock not required)
SerDes port is enabled
Partial termination may be required1
(Reference Clock is required)
1 Partial Termination when a SerDes port is enabled through both POR input and DEVDISR is determined by the
SerDes port mode. If the port is in x8 PCI Express mode, no termination is required because all pins are being used.
If the port is in x1/x2/x4 PCI Express mode, termination is required on the unused pins. If the port is in x4 Serial
RapidIO mode termination is required on the unused pins.
Disabled through DEVDISR
SerDes port is disabled (through POR
input)
Complete termination required
(Reference Clock not required)
SerDes port is disabled after software
disables port
Same termination requirements as when
the port is enabled through POR input2
(Reference Clock is required)
2 If a SerDes port is enabled through the POR input and then disabled through DEVDISR, no hardware changes are
required. Termination of the SerDes port should follow what is required when the port is enabled through both POR
input and DEVDISR. See Note 1 for more information.
Notes:
相關PDF資料 |
PDF描述 |
|---|---|
| MC8641HX1250HB | IC MPU SGL E600 CORE 994FCCBGA |
| MC8641HX1000NC | IC MPU SGL E600 CORE 994FCCBGA |
| MC8641HX1000NB | IC MPU SGL E600 CORE 994FCCBGA |
| 356-006-506-101 | CARDEDGE 6POS .156 BLACK |
| 356-006-500-104 | CARDEDGE 6POS .156 BLACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC8641HX1250J | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8641HX1250K | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8641HX1250N | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8641HX1333G | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8641HX1333H | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
發布緊急采購，3分鐘左右您將得到回復。