- 您現在的位置：買賣IC網 > PDF目錄45378 > MC80C52TXXX-30 (ATMEL CORP) 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MC80C52TXXX-30 |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | 0.600 INCH, SIDE BRAZED, DIP-40 |
| 文件頁數： | 163/234頁 |
| 文件大?。?/td> | 25028K |
| 代理商： | MC80C52TXXX-30 |
34
ATtiny25/45/85 [DATASHEET]
2586Q–AVR–08/2013
7.
Power Management and Sleep Modes
The high performance and industry leading code efficiency makes the AVR microcontrollers an ideal choise for low
power applications. In addition, sleep modes enable the application to shut down unused modules in the MCU,
thereby saving power. The AVR provides various sleep modes allowing the user to tailor the power consumption to
the application’s requirements.
7.1
Sleep Modes
Figure 6-1 on page 23 presents the different clock systems and their distribution in ATtiny25/45/85. The figure is
helpful in selecting an appropriate sleep mode. Table 7-1 shows the different sleep modes and their wake up
sources.
Note:
1. For INT0, only level interrupt.
To enter any of the three sleep modes, the SE bit in MCUCR must be written to logic one and a SLEEP instruction
must be executed. The SM[1:0] bits in the MCUCR Register select which sleep mode (Idle, ADC Noise Reduction
or Power-down) will be activated by the SLEEP instruction. See Table 7-2 for a summary.
If an enabled interrupt occurs while the MCU is in a sleep mode, the MCU wakes up. The MCU is then halted for
four cycles in addition to the start-up time, executes the interrupt routine, and resumes execution from the instruc-
tion following SLEEP. The contents of the Register File and SRAM are unaltered when the device wakes up from
sleep. If a reset occurs during sleep mode, the MCU wakes up and executes from the Reset Vector.
Note that if a level triggered interrupt is used for wake-up the changed level must be held for some time to wake up
the MCU (and for the MCU to enter the interrupt service routine). See “External Interrupts” on page 49 for details.
7.1.1
Idle Mode
When the SM[1:0] bits are written to 00, the SLEEP instruction makes the MCU enter Idle mode, stopping the CPU
but allowing Analog Comparator, ADC, USI, Timer/Counter, Watchdog, and the interrupt system to continue oper-
ating. This sleep mode basically halts clk
CPU and clkFLASH, while allowing the other clocks to run.
Idle mode enables the MCU to wake up from external triggered interrupts as well as internal ones like the Timer
Overflow. If wake-up from the Analog Comparator interrupt is not required, the Analog Comparator can be powered
down by setting the ACD bit in “ACSR – Analog Comparator Control and Status Register” on page 120. This will
reduce power consumption in Idle mode. If the ADC is enabled, a conversion starts automatically when this mode
is entered.
Table 7-1.
Active Clock Domains and Wake-up Sources in the Different Sleep Modes
Active Clock Domains
Oscillators
Wake-up Sources
Sleep Mode
clk
CPU
clk
FLASH
clk
IO
clk
ADC
clk
PCK
Main
Cl
ock
Sour
ce
Enabled
INT0
a
nd
Pin
Ch
ange
SPM/EEPROM
Rea
d
y
USI
S
tart
Co
nditio
n
ADC
Ot
her
I/O
W
a
tchdo
g
Interrupt
Idle
X
XXXXXX
ADC Noise
Reduction
XX
XXX
X
Power-down
XX
相關PDF資料 |
PDF描述 |
|---|---|
| MQ80C32-30SHXXX | 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44 |
| MC80C32-25:D | 8-BIT, 25 MHz, MICROCONTROLLER, CDIP40 |
| MD80C32E-20SHXXX:D | 8-BIT, 20 MHz, MICROCONTROLLER, CDIP40 |
| MD80C52EXXX-36:D | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CDIP40 |
| MQ80C32-12SHXXX:R | 8-BIT, 12 MHz, MICROCONTROLLER, CQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC80D21000G | 制造商:COR 功能描述:RN |
| MC80F0104 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0104B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0104D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0204 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。