- 您現在的位置：買賣IC網 > PDF目錄45249 > MC7447RX867LB (FREESCALE SEMICONDUCTOR INC) 32-BIT, 867 MHz, RISC PROCESSOR, CBGA360 PDF資料下載
參數資料
| 型號： | MC7447RX867LB |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, 867 MHz, RISC PROCESSOR, CBGA360 |
| 封裝： | 25 X 25 MM, 3.24 MM HEIGHT, 1.27 MM PITCH, CERAMIC, BGA-360 |
| 文件頁數： | 52/72頁 |
| 文件大小： | 1598K |
| 代理商： | MC7447RX867LB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MPC7457 RISC Microprocessor Hardware Specifications, Rev. 7
56
Freescale Semiconductor
System Design Information
If address or data parity is not used by the system, and the respective parity checking is disabled through
HID0, the input receivers for those pins are disabled, and those pins do not require pull-up resistors and
should be left unconnected by the system. If all parity generation is disabled through HID0, all parity
checking should also be disabled through HID0, and all parity pins may be left unconnected by the system.
The L3 interface does not normally require pull-up resistors. Unused L3_ADDR signals are driven low
when the SRAM is configured to be less than 1 M in size via L3CR. For example, L3_ADD[18] will be
driven low if the SRAM size is configured to be 2 M; likewise, L3_ADDR[18:17] will be driven low if
the SRAM size is configured to be 1 M.
9.7
JTAG Configuration Signals
Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the
IEEE 1149.1 specification, but is provided on all processors that implement the PowerPC architecture.
While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, more
reliable power-on reset performance will be obtained if the TRST signal is asserted during power-on reset.
Because the JTAG interface is also used for accessing the common on-chip processor (COP) function,
simply tying TRST to HRESET is not practical.
The COP function of these processors allows a remote computer system (typically, a PC with dedicated
hardware and debugging software) to access and control the internal operations of the processor. The COP
interface connects primarily through the JTAG port of the processor, with some additional status
monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order
to fully control the processor. If the target system has independent reset sources, such as voltage monitors,
watchdog timers, power supply failures, or push-button switches, the COP reset signals must be merged
into these signals with logic.
The arrangement shown in Figure 26 allows the COP port to independently assert HRESET or TRST,
while ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not
be used, TRST should be tied to HRESET through a 0-Ω isolation resistor so that it is asserted when the
system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during
power-on. While Freescale recommends that the COP header be designed into the system as shown in
Figure 26, if this is not possible, the isolation resistor will allow future access to TRST in the case where
a JTAG interface may need to be wired onto the system in debug situations.
The COP header shown in Figure 26 adds many benefits—breakpoints, watchpoints, register and memory
examination/modification, and other standard debugger features are possible through this interface—and
can be as inexpensive as an unpopulated footprint for a header to be added when needed.
The COP interface has a standard header for connection to the target system, based on the 0.025"
square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has
pin 14 removed as a connector key.
There is no standardized way to number the COP header shown in Figure 26; consequently, many different
pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in
Figure 26 is common to all known emulators.
相關PDF資料 |
PDF描述 |
|---|---|
| MC7448VS1267NC | 32-BIT, 1267 MHz, RISC PROCESSOR, CBGA360 |
| MC7448VU1400NC | 32-BIT, 1400 MHz, RISC PROCESSOR, CBGA360 |
| MC7448HX600NC | 32-BIT, 600 MHz, RISC PROCESSOR, CBGA360 |
| MC7448VU1400ND | 32-BIT, 1400 MHz, RISC PROCESSOR, CBGA360 |
| MC7448VU1267ND | 32-BIT, 1267 MHz, RISC PROCESSOR, CBGA360 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC7447RX867NB | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:PPC7457RX1000NB |
| MC7448HX1000LC | 功能描述:IC MPU RISC 32BIT 360-FCCBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC74xx 標準包裝:1 系列:MPC85xx 處理器類型:32-位 MPC85xx PowerQUICC III 特點:- 速度:1.2GHz 電壓:1.1V 安裝類型:表面貼裝 封裝/外殼:783-BBGA，F(xiàn)CBGA 供應商設備封裝:783-FCPBGA（29x29） 包裝:托盤 |
| MC7448HX1000LD | 功能描述:微處理器 - MPU APL8 RV2.2.1 1.15V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MC7448HX1000N | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC7448 Hardware Specifications |
| MC7448HX1000NC | 功能描述:IC MPU RISC 32BIT 360-FCCBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC74xx 標準包裝:1 系列:MPC85xx 處理器類型:32-位 MPC85xx PowerQUICC III 特點:- 速度:1.2GHz 電壓:1.1V 安裝類型:表面貼裝 封裝/外殼:783-BBGA，F(xiàn)CBGA 供應商設備封裝:783-FCPBGA（29x29） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。