參數資料
型號： MC705JJ7CDWE
廠商： Freescale Semiconductor
文件頁數： 28/164頁
文件大?。?/td> 0K
描述： IC MCU 8BIT 224B RAM 20-SOIC
標準包裝： 38
系列： HC05
核心處理器： HC05
芯體尺寸： 8-位
速度： 2.1MHz
連通性： SIO
外圍設備： POR，溫度傳感器，WDT
輸入/輸出數： 14
程序存儲器容量： 6KB（6K x 8）
程序存儲器類型： OTP
RAM 容量： 224 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 4x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
包裝： 管件
EPROM Erasing
MC68HC705JJ7 MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
Freescale Semiconductor
123
13.3.1 MOR Programming
The contents of the MOR should be programmed using the programmer board. To program any bits in
the MOR, the desired bit states must be written to the MOR address and then the MPGM bit in the EPROG
register must be used. The following sequence will program the MOR:
1.
Write the desired data to the MOR location ($1FF1).
2.
Apply the programming voltage to the IRQ/VPP pin.
3.
Set the MPGM bit in the EPROG.
4.
Wait for the programming time, tMPGM.
5.
Clear the MPGM bit in the EPROG.
6.
Remove the programming voltage from the IRQ/VPP pin.
Once the MOR bits have been programmed, some of the options may experience glitches in operation
after removal of the programming voltage. It is recommended that the part be reset before trying to verify
the contents of the user EPROM or the MOR itself.
NOTE
The contents of the EPROM or the MOR cannot be accessed if the
EPMSEC bit in the COPR register has been set.
13.3.2 EPMSEC Programming
The EPMSEC bit is programmable. To program the EPMSEC bit, the desired state must be written to the
COP address and then the MPGM bit in the EPROG register must be used. The following sequence will
program the EPMSEC bit:
1.
Write the desired data to bit 7 of the COPR location ($1FF0).
2.
Apply the programming voltage to the IRQ/VPP pin.
3.
Set the MPGM bit in the EPROG.
4.
Wait for the programming time, tMPGM.
5.
Clear the MPGM bit in the EPROG.
6.
Remove the programming voltage from the IRQ/VPP pin.
Once the EPMSEC bit has been programmed to a logic 1, access to the contents of the EPROM and MOR
in the expanded non-user modes will be denied. It is therefore recommended that the user EPROM and
MOR in the part first be programmed and fully verified before setting the EPMSEC bit.
13.4 EPROM Erasing
MCUs with windowed packages permit EPROM erasing with ultraviolet light. Erase the EPROM by
exposing it to 15 Ws/cm2 of ultraviolet light with a wavelength of 2537 angstroms. Position the ultraviolet
light source 1 inch from the window. Do not use a shortwave filter. The erased state of an EPROM bit is
a logic 0.
NOTE
Unlike many commercial EPROMs, an erased EPROM byte in the MCU will
read as $00. All unused locations should be programmed as 0s.
相關PDF資料
PDF描述
VI-B1H-IY-F4 CONVERTER MOD DC/DC 52V 50W
VE-B43-IX-B1 CONVERTER MOD DC/DC 24V 75W
AD724JRZ-RL IC ENCODER RGB TO NTSC 16SOIC TR
VE-B42-IX-B1 CONVERTER MOD DC/DC 15V 75W
VI-B1F-IY-F3 CONVERTER MOD DC/DC 72V 50W
相關代理商/技術參數
參數描述
MC705JJ7CDWE 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MC705JP7CPE 功能描述:8位微控制器 -MCU 8B MCU 224 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705JP7CPE 制造商:Freescale Semiconductor 功能描述:IC 8BIT MCU 68HC05 2.1MHZ DIP-28
MC705K1CP 制造商:Motorola Inc 功能描述:16 PIN DIP INTEGRATED CIRCUIT
MC705L16CFUE 功能描述:8位微控制器 -MCU 8B MCU W/ EPROM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*