參數資料
型號： MC68L11F1CFNE3
廠商： Freescale Semiconductor
文件頁數： 101/158頁
文件大?。?/td> 0K
描述： IC MCU 8BIT 3MHZ 68-PLCC
標準包裝： 18
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 3MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 30
程序存儲器類型： ROMless
EEPROM 大?。?/td> 512 x 8
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 68-LCC（J 形引線）
包裝： 管件
OPERATING MODES AND ON-CHIP MEMORY
TECHNICAL DATA
4-9
4.3.2 Initialization
Because bits in the following registers control the basic configuration of the MCU, an
accidental change of their values could cause serious system problems. The protec-
tion mechanism, overridden in special operating modes, requires a write to the protect-
ed bits only within the first 64 bus cycles after any reset, or only once after each reset.
Table 4-2 summarizes the write access limited registers.
4.3.2.1 CONFIG Register
CONFIG controls the presence and position of the EEPROM in the memory map.
CONFIG also enables the COP watchdog timer.
P indicates a previously programmed bit. P(L) indicates that the bit resets to the logic
level held in the latch prior to reset, but the function of COP is controlled by DISR bit
in TEST1 register.
The CONFIG register consists of an EEPROM byte and static latches that control the
start-up conguration of the MCU. The contents of the EEPROM byte are transferred
into static working latches during reset sequences. The operation of the MCU is con-
trolled directly by these latches and not by CONFIG itself. In normal modes, changes
to CONFIG do not affect operation of the MCU until after the next reset sequence.
When programming, the CONFIG register itself is accessed. When the CONFIG reg-
ister is read, the static latches are accessed.
These bits can be read at any time. The value read is the one latched into the register
from the EEPROM cells during the last reset sequence. A new value programmed into
this register cannot be read until after a subsequent reset sequence. Unused bits al-
ways read as ones.
In special test mode, the static latches can be written directly at any time. In all modes,
CONFIG bits can only be programmed using the EEPROM programming sequence,
and are neither readable nor active until latched via the next reset. Refer to 4.4.3 CON-
EE[3:0] — EEPROM Mapping Control
EE[3:0] select the upper four bits of the EEPROM base address. In single-chip and
bootstrap modes, EEPROM is forced to $FE00–$FFFF regardless of the value of
EE[3:0].
CONFIG — System Configuration Register
$103F
Bit 7
654321
Bit 0
EE3
EE2
EE1
EE0
—
NOCOP
—
EEON
RESET:
11111
P
11
Single Chip
11111
P(L)
1
Bootstrap
P
P1P1P
Expanded
PPPP
1
P(L)
1
0
Special Test
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
VE-B1B-CU-F3 CONVERTER MOD DC/DC 95V 200W
MC68L11E1FNE2 IC MCU 8BIT 2MHZ 52-PLCC
VE-B1B-CU-F2 CONVERTER MOD DC/DC 95V 200W
MC68L11E1CFNE2 IC MCU 8BIT 2MHZ 52-PLCC
VE-B1B-CU-F1 CONVERTER MOD DC/DC 95V 200W
相關代理商/技術參數
參數描述
MC68L11K1FN2R2 制造商:Motorola Inc 功能描述:
MC68L11K1FUE2 功能描述:8位微控制器 -MCU 8B MCU L-VOLTAGE-EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FN2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68L711E9FNE2 功能描述:8位微控制器 -MCU 8B MCU LO VOLTAGE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FU2 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*