參數資料
型號: MC68HC11EA9MFN3
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC52
封裝: PLASTIC, LCC-52
文件頁數: 19/58頁
文件大?。?/td> 583K
代理商: MC68HC11EA9MFN3
MOTOROLA
MC68HC11EA9
26
MC68HC11EA9TS/D
6 Parallel Input/Output
The MC68HC(7)11EA9 has up to 36 input/output lines, depending on the operating mode. Table 10
shows the configuration and features of each port.
Simple and full handshake input and output functions are available on ports B and C lines in single-chip
mode. The following is a description of the handshake functions.
In simple strobed mode, port B is a strobed output port and port C is a latching input port. The two ac-
tivities are available simultaneously.
The STRB output is pulsed for two E-clock periods each time there is a write to the PORTB register.
The INVB bit in the PIOC register controls the polarity of STRB pulses. Port C levels are latched into
the alternate port C latch (PORTCL) register on each assertion of the STRA input. STRA edge select,
flag, and interrupt enable bits are located in the PIOC register. Any or all of the port C lines can still be
used as general-purpose I/O while in strobed input mode.
Full handshake modes involve port C pins and the STRA and STRB lines. Input and output handshake
modes are supported, and output handshake mode has a three-stated variation. STRA is an edge de-
tecting input, and STRB is a handshake output. Control and enable bits are located in the PIOC register.
In full input handshake mode, the MCU uses STRB as a ready line to an external system. Port C logic
levels are latched into PORTCL when the STRA line is asserted by the external system. The MCU then
negates STRB. The MCU reasserts STRB after the PORTCL register is read. A mix of latched inputs,
static inputs, and static outputs is allowed on port C, differentiated by the data direction bits and use of
the PORTC and PORTCL registers.
In full output handshake mode, the MCU writes data to PORTCL which, in turn, asserts the STRB output
to indicate that data is ready. The external system reads port C and asserts the STRA input to acknowl-
edge that data has been received.
In the three-state variation of output handshake mode, lines intended as three-state handshake outputs
are configured as inputs by clearing the corresponding DDRC bits. The MCU writes data to PORTCL
and asserts STRB. The external system responds by activating the STRA input, which forces the MCU
to drive the data in PORTCL out on all of the port C lines. The mode variation does not allow part of port
C to be used for static inputs while other port C pins are being used for handshake outputs. Refer to
PIOC register description for further information.
Table 10 I/O Port Configuration
Port
Input
Pins
Output
Pins
Bidirectional
Pins
Shared Functions
A
8
Timer
B
8
High Order Address
C
8
Multiplexed Low Order Address/Data
D
2
SCI/PLL Test
E
8
A/D Converter
1
XPIN (XIRQ pin configured for data input)
1
IPIN (IRQ pin configured for data input)
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HC711KS2VFN4 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQCC68
MC68HC711K4VFU4 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80
MC68HC711KS2CPU3 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PQFP80
MC68HC711K4CFU3 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PQFP80
MC68HC711K4MFU4 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
MC68HC11EA9MP2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
MC68HC11EA9MP3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
MC68HC11EA9VFN2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
MC68HC11EA9VFN3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
MC68HC11EA9VP2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers