- 您現在的位置：買賣IC網 > PDF目錄359663 > MC68HC11A0CFN1 (飛思卡爾半導體(中國)有限公司) ROM-based high-performance microcontrollers PDF資料下載
參數資料
| 型號： | MC68HC11A0CFN1 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | ROM-based high-performance microcontrollers |
| 中文描述： | 基于ROM的高性能微控制器 |
| 文件頁數： | 85/124頁 |
| 文件大?。?/td> | 840K |
| 代理商： | MC68HC11A0CFN1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
SERIAL PERIPHERAL INTERFACE
TECHNICAL DATA
8-7
8.5.2 Serial Peripheral Status
SPIF — SPI Transfer Complete Flag
SPIF is set upon completion of data transfer between the processor and the external
device. If SPIF goes high, and if SPIE is set, a serial peripheral interrupt is generated.
To clear the SPIF bit, read the SPSR with SPIF set, then access the SPDR. Unless
SPSR is read (with SPIF set) first, attempts to write SPDR are inhibited.
WCOL — Write Collision
Clearing the WCOL bit is accomplished by reading the SPSR (with WCOL set) fol-
lowed by an access of SPDR. Refer to
8.3.4 Slave Select
and
8.4 SPI System Errors
.
0 = No write collision
1 = Write collision
Bit 5 — Not implemented
Always reads zero
MODF — Mode Fault
To clear the MODF bit, read the SPSR (with MODF set), then write to the SPCR. Refer
to
8.3.4 Slave Select
and
8.4 SPI System Errors
.
0 = No mode fault
1 = Mode fault
Bits [3:0] — Not implemented
Always read zero
8.5.3 Serial Peripheral Data I/O
The SPDR is used when transmitting or receiving data on the serial bus. Only a write
to this register initiates transmission or reception of a byte, and this only occurs in the
master device. At the completion of transferring a byte of data, the SPIF status bit is
set in both the master and slave devices.
A read of the SPDR is actually a read of a buffer. To prevent an overrun and the loss
of the byte that caused the overrun, the first SPIF must be cleared by the time a second
transfer of data from the shift register to the read buffer is initiated.
NOTE
SPI is double buffered in and single buffered out.
SPSR
— Serial Peripheral Status Register
$0029
Bit 7
SPIF
0
6
5
0
0
4
3
0
0
2
0
0
1
0
0
Bit 0
0
0
WCOL
0
MODF
0
RESET:
SPDR
— SPI Data Register
$002A
Bit 7
Bit 7
6
6
5
5
4
4
3
3
2
2
1
1
Bit 0
Bit 0
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11A0CFN4 | ROM-based high-performance microcontrollers |
| MC68HC11A0CFU | ROM-based high-performance microcontrollers |
| MC68HC11A0CFU1 | ROM-based high-performance microcontrollers |
| MC68HC11A0CFU4 | ROM-based high-performance microcontrollers |
| MC68HC11A0FB | ROM-based high-performance microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11A0CFN2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller |
| MC68HC11A0CFN3 | 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: |
| MC68HC11A0CFN3R2 | 制造商:Rochester Electronics LLC 功能描述: |
| MC68HC11A0CFN4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11A0CFNE3 | 功能描述:8位微控制器 -MCU 8B MCU 768RAM A/D 3MH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。