參數資料
型號: MC68HC11A0CFN1
廠商: 飛思卡爾半導體(中國)有限公司
英文描述: ROM-based high-performance microcontrollers
中文描述: 基于ROM的高性能微控制器
文件頁數: 71/124頁
文件大?。?/td> 840K
代理商: MC68HC11A0CFN1
SERIAL COMMUNICATIONS INTERFACE
For More Information On This Product,
Go to: www.freescale.com
TECHNICAL DATA
7-5
7.5 SCI Error Detection
Three error conditions, SCDR overrun, received bit noise, and framing can occur dur-
ing generation of SCI system interrupts. Three bits (OR, NF, and FE) in the serial com-
munications status register (SCSR) indicate if one of these error conditions exists. The
overrun error (OR) bit is set when the next byte is ready to be transferred from the re-
ceive shift register to the SCDR and the SCDR is already full (RDRF bit is set). When
an overrun error occurs, the data that caused the overrun is lost and the data that was
already in SCDR is not disturbed. The OR is cleared when the SCSR is read (with OR
set), followed by a read of the SCDR.
The noise flag (NF) bit is set if there is noise on any of the received bits, including the
start and stop bits. The NF bit is not set until the RDRF flag is set. The NF bit is cleared
when the SCSR is read (with FE equal to one) followed by a read of the SCDR.
When no stop bit is detected in the received data character, the framing error (FE) bit
is set. FE is set at the same time as the RDRF. If the byte received causes both fram-
ing and overrun errors, the processor only recognizes the overrun error. The framing
error flag inhibits further transfer of data into the SCDR until it is cleared. The FE bit is
cleared when the SCSR is read (with FE equal to one) followed by a read of the SCDR.
7.6 SCI Registers
There are five addressable registers in the SCI.
7.6.1 Serial Communications Data Register (SCDR)
SCDR is a parallel register that performs two functions. It is the receive data register
when it is read, and the transmit data register when it is written. Reads access the re-
ceive data buffer and writes access the transmit data buffer. Receive and transmit are
double buffered.
*U = Unaffected
7.6.2 Serial Communications Control Register 1 (SCCR1)
The SCCR1 register provides the control bits that determine word length and select
the method used for the wake-up feature.
R8 — Receive Data Bit 8
If M bit is set, R8 stores the ninth bit in the receive data character.
SCDR
— SCI Data Register
$002F
Bit 7
R7/T7
U*
6
5
4
3
2
1
Bit 0
R0/T0
U
R6/T6
U
R5/T5
U
R4/T4
U
R3/T3
U
R2/T2
U
R1/T1
U
RESET:
SCCR1
— SCI Control Register 1
$002C
Bit 7
R8
U
6
5
0
0
4
M
0
3
2
0
0
1
0
0
Bit 0
0
0
T8
U
WAKE
0
RESET:
F
Freescale Semiconductor, Inc.
n
.
相關PDF資料
PDF描述
MC68HC11A0CFN4 ROM-based high-performance microcontrollers
MC68HC11A0CFU ROM-based high-performance microcontrollers
MC68HC11A0CFU1 ROM-based high-performance microcontrollers
MC68HC11A0CFU4 ROM-based high-performance microcontrollers
MC68HC11A0FB ROM-based high-performance microcontrollers
相關代理商/技術參數
參數描述
MC68HC11A0CFN2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A0CFN3 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC11A0CFN3R2 制造商:Rochester Electronics LLC 功能描述:
MC68HC11A0CFN4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11A0CFNE3 功能描述:8位微控制器 -MCU 8B MCU 768RAM A/D 3MH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT