- 您現在的位置：買賣IC網 > PDF目錄45219 > MC68HC05C9ECP (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 PDF資料下載
參數資料
| 型號： | MC68HC05C9ECP |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | PLASTIC, DIP-40 |
| 文件頁數： | 143/144頁 |
| 文件大?。?/td> | 1628K |
| 代理商： | MC68HC05C9ECP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁當前第143頁第144頁
N
O
N-D
I
SC
L
O
SU
R
E
AG
R
EEMENT
R
E
Q
U
IR
ED
Serial Peripheral Interface (SPI)
Advance Information
MC68HC05C9E
98
Serial Peripheral Interface (SPI)
MOTOROLA
SPIF set) followed by an access of the SPDR. Following the initial
transfer, unless SPSR is read (with SPIF set) first, attempts to write to
SPDR are inhibited.
WCOL — Write Collision Bit
The write collision bit is set when an attempt is made to write to the
serial peripheral data register while data transfer is taking place. If
CPHA is 0, a transfer is said to begin when SS goes low and the
transfer ends when SS goes high after eight clock cycles on SCK.
When CPHA is 1, a transfer is said to begin the first time SCK
becomes active while SS is low and the transfer ends when the SPIF
flag gets set. Clearing the WCOL bit is accomplished by reading the
SPSR (with WCOL set) followed by an access to SPDR.
MODF — Mode Fault Flag
The mode fault flag indicates that there may have been a multi-master
conflict for system control and allows a proper exit from system
operation to a reset or default system state. The MODF bit is normally
clear, and is set only when the master device has its SS pin pulled
low. Setting the MODF bit affects the internal serial peripheral
interface system in these ways:
1. An SPI interrupt is generated if SPIE = 1.
2. The SPE bit is cleared. This disables the SPI.
3. The MSTR bit is cleared, thus forcing the device into the
slave mode.
Clearing the MODF bit is accomplished by reading the SPSR (with
MODF set), followed by a write to the SPCR. Control bits SPE and
MSTR may be restored by user software to their original state during
this clearing sequence or after the MODF bit has been cleared. It is
also necessary to restore DDRD after a mode fault.
Bits 5 and 3–0 — Not Implemented
These bits always read 0.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05C9FB | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC05C9CB | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP42 |
| MC68HC05C9FN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05C9CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05C9P | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05CT4FB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification |
| MC68HC05CT4FN | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification |
| MC68HC05D9 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-bit microcomputer with PWM outputs and LED drive |
| MC68HC05E0 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:High-density complementary metal oxide semiconductor (HCMOS) microcontroller unit |
| MC68HC05E0FN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。