- 您現在的位置：買賣IC網 > PDF目錄385566 > MC33153 (ON SEMICONDUCTOR) Single IGBT Gate Driver(單IGBT門驅動器) PDF資料下載
參數資料
| 型號： | MC33153 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Single IGBT Gate Driver(單IGBT門驅動器) |
| 中文描述： | 單IGBT柵極驅動器（單IGBT的門驅動器） |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 194K |
| 代理商： | MC33153 |
MC33153
http://onsemi.com
11
APPLICATION INFORMATION
Figure 34 shows a basic IGBT driver application. When
driven from an optoisolator, an input pull up resistor is
required. This resistor value should be set to bias the output
transistor at the desired current. A decoupling capacitor
should be placed close to the IC to minimize switching noise.
A bootstrap diode may be used for a floating supply. If the
protection features are not required, then both the Fault
Blanking/Desaturation and Current Sense Inputs should
both be connected to the Kelvin Ground (Pin 2). When used
with a single supply, the Kelvin Ground and V
EE
pins should
be connected together. Separate gate resistors are
recommended to optimize the turn
on and turn
off drive.
Figure 34. Basic Application
7
4
3
2
1
5
8
6
Fault
Input
Desat/
Blank
Output
Sense
Gnd
V
EE
V
CC
MC33153
18 V
B+
Bootstrap
Figure 35. Dual Supply Application
7
4
3
2
1
5
8
6
Fault
Input
Desat/
Blank
Output
Sense
Gnd
V
EE
V
CC
MC33153
15 V
5.0 V
When used in a dual supply application as in Figure 35, the
Kelvin Ground should be connected to the emitter of the
IGBT. If the protection features are not used, then both the
Fault Blanking/Desaturation and the Current Sense Inputs
should be connected to Ground. The input optoisolator
should always be referenced to V
EE
.
If desaturation protection is desired, a high voltage diode
is connected to the Fault Blanking/Desaturation pin. The
blanking capacitor should be connected from the
Desaturation pin to the V
EE
pin. If a dual supply is used, the
blanking capacitor should be connected to the Kelvin
Ground. The Current Sense Input should be tied high
because the two comparator outputs are ANDed together.
Although the reverse voltage on collector of the IGBT is
clamped to the emitter by the free
wheeling diode, there is
normally considerable inductance within the package itself.
A small resistor in series with the diode can be used to
protect the IC from reverse voltage transients.
Figure 36. Desaturation Application
7
4
3
2
1
5
8
6
Fault
Input
Desat/
Blank
Output
Sense
Gnd
V
EE
V
CC
MC33153
18 V
C
Blank
When using sense IGBTs or a sense resistor, the sense
voltage is applied to the Current Sense Input. The sense trip
voltages are referenced to the Kelvin Ground pin. The sense
voltage is very small, typically about 65 mV, and sensitive
to noise. Therefore, the sense and ground return conductors
should be routed as a differential pair. An RC filter is useful
in filtering any high frequency noise. A blanking capacitor
is connected from the blanking pin to V
EE
. The stray
capacitance on the blanking pin provides a very small level
of blanking if left open. The blanking pin should not be
grounded when using current sensing, that would disable the
sense. The blanking pin should never be tied high, that
would short out the clamp transistor.
Figure 37. Sense IGBT Application
7
4
3
2
1
5
8
6
Fault
Input
Desat/
Blank
Output
Sense
Gnd
V
EE
V
CC
MC33153
18 V
相關PDF資料 |
PDF描述 |
|---|---|
| MC33157 | Tag-it(TM) HF-I Plus Transponder Inlays Square 0-RFIDN -25 to 70 |
| MC33157DW | Tag-it(TM) HF-I Standard Transponder Inlays Square 0-RFIDN -25 to 70 |
| MC33160 | 100 mA, 5.0 V Voltage Regulator and Supervisory Circuit for Microprocessors(100 mA, 5.0 V電壓穩壓器和微處理器監控電路) |
| MC33161DR2G | Universal Voltage Monitors |
| MC33161PG | Universal Voltage Monitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33153 | 制造商:SPC Multicomp 功能描述:PTC Resettable Fuse |
| MC33153_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Single IGBT Gate Driver |
| MC33153D | 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33153DG | 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33153DR2 | 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。