- 您現在的位置：買賣IC網 > PDF目錄45193 > MB91F313APMC-GE1 (FUJITSU LTD) 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91F313APMC-GE1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, LFQFP-120 |
| 文件頁數： | 10/72頁 |
| 文件大小： | 1975K |
| 代理商： | MB91F313APMC-GE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MB91313/A Series
18
DS07-16706-3E
■ HANDLING DEVICES
Preventing latch-up
Latch-up may occur in a CMOS IC if a voltage higher than VDDE or VDDI, or less than VSS is applied to an input or
output pin or if a voltage exceeding the rating is applied between VDDE and VSS, or VDDI and VSS. If latch-up
occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the device.
Therefore, be very careful not to apply voltages in excess of the absolute maximum ratings.
Handling of unused input pins
If unused input pins are left open, abnormal operation may result. Any unused input pins should be connected
to pull-up or pull-down resistor.
Power supply pins
In MB91313/A series, devices including multiple of VDDE pins, VDDI pins and VSS pins are designed as follows;
pins necessary to be at the same potential are interconnected internally to prevent malfunctions such as latch-up.
All of the power supply pin and GND pin must be externally connected to the power supply and ground respectively
in order to reduce unnecessary radiation, to prevent strobe signal malfunctions due to the ground level rising and
to follow the total output current ratings. Furthermore, the VDDE pins, VDDI pins and VSS pins of the MB91313/
A series must be connected to the current supply source via a low impedance. It is also recommended to connect
a ceramic capacitor of approximately 0.1
F as a bypass capacitor between VDDE pins, VDDI pins and VSS pins
near this device.
Crystal oscillator circuit
Noise in proximity to the X0 and X1 (X0A, X1A) pins can cause the device to operate abnormally. Printed circuit
boards should be designed so that the X0 (X0A) and X1 (X1A) pins, and crystal oscillator, as well as bypass
capacitors connected to ground, are located near the device and ground.
It is recommended that the printed circuit board artwork be designed such that the X0 and X1 pins or X0A and
X1A pins are surrounded by ground plane for the stable operation.
Please request the oscillator manufacturer to evaluate the oscillational characteristics of the crystal and this
device.
Mode pins (MD0 to MD2)
When using mode pins, connect them directly to power supply pin or GND pin. To prevent the device from
entering test mode accidentally due to noise, minimize the lengths of the patterns between each mode pin and
power supply pin or GND pin on the printed circuit board as possible and connect them with low impedance.
Operation at power-on
Ensure that the INITX pin is reset and the settings are initialized (INIT) immediately after the power is turned on.
Maintain the “L” level input to the INITX pin during the stabilization wait time immediately after the power on to
ensure the stabilization wait time as required by the oscillator circuit (the stabilization wait time is reset to the
minimum value when INIT is asserted using the INITX pin).
Note on oscillator input at power-on
At power-on, ensure that the clock is input until the oscillator stabilization wait time has elapsed.
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F313APMC-GE1 | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F345BPFT-GE1 | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91F355APMT | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91F365GB | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F366GB | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F314 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F314PMC-GE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F318A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F318R | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91F318RPMC-G-XXXE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。