參數資料
型號： MB90F822PFM
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80
封裝： 0.65 MM, PLASTIC, LQFP-80
文件頁數： 8/98頁
文件大?。?/td> 1383K
代理商： MB90F822PFM
MB90820 Series
16
s HANDLING DEVICES
1.
Preventing latch-up
CMOS ICs may cause latch-up in the following situations:
When a voltage higher than VCC or lower than VSS is applied to input or output pins.
When a voltage exceeding the rating is applied between VCC and VSS.
When the AVCC power supply is applied before the VCC voltage.
If latch-up occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Use meticulous care not to exceed the rating.
For the same reason, also be careful not to let the analog power-supply voltage exceed the digital power-supply
voltage.
2.
Handling unused pins
Unused input pins left open may cause abnormal operations, or latch-up leading to permanent damage. Unused
input pins should be pulled up or pulled down through at least 2 k
resistance.
Unused input/output pins may be left open in output state, but if such pins are in input state they should be
handled in the same way as input pins.
If any output pins are unused, set them to open.
3.
Use of the external clock
To use an external clock, drive only the X0 pin and leave the X1 pin open (See the illustration below).
4.
Power supply pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground lines to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS near
this device.
5.
Crystal oscillator circuit
Noise near the X0 and X1 pins may cause the device to malfunction. Design the printed circuit board so that
X0, X1, the crystal oscillator (or ceramic oscillator) and the bypass capacitor to ground are located as close to
the device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1 pins surrounded by ground plane
because stable operation can be expected with such a layout.
6.
Turning-on sequence of power supply to A/D converter and D/A converter
Make sure to turn on the A/D converter and D/A converter power supply (AVCC, AVSS, AVR) and analog inputs
(AN0 to AN15) after turning-on the digital power supply (VCC).
MB90820 series
Open
X0
X1
相關PDF資料
PDF描述
MB90F867ESPMC 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
MB90F867EPMC 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
MB90867EPMC 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
MB90F882ASPMC 16-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP100
MB90F883CSPMC 16-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB90F867APFR-G-SNE1 制造商:FUJITSU 功能描述:
MB90F867ASPF-GE1 制造商:FUJITSU 功能描述:IC 16BIT MCU I2C SMD QFP100
MB90F867ASPFR-GE1 制造商:FUJITSU 功能描述:
MB90F867ASPFR-G-SPE1 制造商:FUJITSU 功能描述:
MB90F897PMCR-G-TE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*