- 您現在的位置：買賣IC網 > PDF目錄2092 > MAX9888EWY+T (Maxim Integrated Products)IC CODEC AUDIO FLEXSOUND 63WLP PDF資料下載
參數資料
| 型號： | MAX9888EWY+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 65/115頁 |
| 文件大小： | 0K |
| 描述： | IC CODEC AUDIO FLEXSOUND 63WLP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive®, FLEXSOUND™ |
| 類型： | D 類 |
| 輸出類型： | 3 通道，帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 1.37W x 2 @ 8 歐姆; 40mW x 2 @ 16 歐姆 |
| 電源電壓： | 2.8 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，I²S，麥克風，靜音，關機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 63-WLP |
| 封裝/外殼： | 63-WFBGA，WLCSP |
| 包裝： | 帶卷 (TR) |
| 配用： | MAX9888EVKIT+-ND - KIT EVALUATION FOR MAX9888 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
Stereo Audio CODEC
with FlexSound Technology
MAX9888
53
Detailed Description
The MAX9888 is a fully integrated stereo audio codec
with FlexSound technology and integrated amplifiers.
Two differential microphone amplifiers can accept sig-
nals from three analog inputs. One input can be retasked
to support two digital microphones. Any combination of
two microphones (analog or digital) can be recorded
simultaneously. The analog signals are amplified up
to 50dB and recorded by the stereo ADC. The digital
record path supports voice filtering with selectable
preset highpass filters and high stopband attenuation
at fS/2. An automatic gain control (AGC) circuit moni-
tors the digitized signal and automatically adjusts the
analog microphone gain to make best use of the ADC’s
dynamic range. A noise gate attenuates signals below
the user-defined threshold to minimize the noise output
by the ADC.
The IC includes two analog line inputs. One of the line
inputs can be optionally retasked as a third analog micro-
phone input. Both line inputs support either stereo single-
ended input signals or mono differential signals. The line
inputs are preamplified and then routed either to the ADC
for recording or to the output amplifiers for playback.
Integrated analog switches allow two differential micro-
phone signals to be routed out the third microphone
input to an external device. This eliminates the need
for an external analog switch in systems that have two
devices recording signals from the same microphone.
Through two digital audio interfaces, the device can
transmit one stereo audio signal and receive two stereo
audio signals in a wide range of formats including I2S,
PCM, and up to four mono slots in TDM. Each interface
can be connected to either of two audio ports (S1 and
S2) for communication with external devices. Both audio
interfaces support 8kHz to 96kHz sample rates. Each
input signal is independently equalized using 5-band
parametric equalizers. A multiband automatic level
control (ALC) boosts signals by up to 12dB. One signal
path additionally supports the same voiceband filtering
as the ADC path.
The IC includes a differential receiver amplifier, stereo
Class D speaker amplifiers, and DirectDrive true ground
stereo headphone amplifiers.
When the receiver amplifier is disabled, analog switches
allow RECP/RXINP and RECN/RXINN to be reused for
signal routing. In systems where a single transducer is
used for both the loudspeaker and receiver, an exter-
nal receiver amplifier can be routed to the left speaker
through RECP/RXINP and RECN/RXINN, bypassing the
Class D amplifier, to connect to the loudspeaker. If the
internal receiver amplifier is used, then leave RECP/
RXINP and RECN/RXINN unconnected. In systems
where an external amplifier drives both the receiver and
the MAX9888’s input, one of the differential signals can
be disconnected from the receiver when not needed
by passing it through the analog switch that connects
RECP/RXINP to RECN/RXINN.
The stereo Class D amplifier provides efficient amplifi-
cation for two speakers. The amplifier includes active
emissions limiting to minimize the radiated emissions
(EMI) traditionally associated with Class D. In most
systems, no output filtering is required to meet standard
EMI limits.
To optimize speaker sound quality, the IC includes an
excursion limiter, a distortion limiter, and a power limiter.
The excursion limiter is a dynamic highpass filter with
variable corner frequency that increases in response
to high signal levels. Low-frequency energy typically
causes more distortion than useful sound at high sig-
nal levels, so attenuating low frequencies allows the
speaker to play louder without distortion or damage. At
lower signal levels, the filter corner frequency reduces
to pass more low frequency energy when the speaker
can handle it. The distortion limiter reduces the volume
when the output signal exceeds a preset distortion level.
This ensures that regardless of input signal and battery
voltage, excessive distortion is never heard by the user.
The power limiter monitors the continuous power into the
loudspeaker and lowers the signal level if the speaker is
at risk of overheating.
The stereo DirectDrive headphone amplifier uses an
inverting charge pump to generate a ground-referenced
output signal. This eliminates the need for DC-blocking
capacitors or a midrail bias for the headphone jack
ground return. Ground sense reduces output noise
caused by ground return current.
The IC integrates jack detection allowing the detection
of insertion and removal of accessories as well as button
presses.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9890AEBL+T | IC SUPP CLICK-POP 9-UCSP |
| MAX9892ELT+T | IC ELIMINATOR CLICK/POP 6UDFN |
| MAX995EUD+ | IC COMPARATOR R-R 14-TSSOP |
| MAX9967ADCCQ+D | IC DCL DUAL 500MBPS ATE 100TQFP |
| MAX998EUT-T | IC COMP SNGL HI-SPEED LP SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9889EWO+T | 功能描述:接口—CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| MAX988ESA | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX988ESA+ | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX988ESA+T | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX988ESA-T | 功能描述:校驗器 IC Single uPower Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。