參數資料
型號： MAX9776EBX+TG45
廠商： Maxim Integrated Products
文件頁數： 18/38頁
文件大?。?/td> 0K
描述： IC AMP AUDIO PWR 1.5W MONO 36WLP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
系列： DirectDrive®
類型： D 類
輸出類型： 1-通道（單聲道），帶立體聲耳機
在某負載時最大輸出功率 x 通道數量： 1.5W x 1 @ 4 歐姆; 60mW x 2 @ 16 歐姆
電源電壓： 2.7 V ~ 5.5 V
特點： 消除爆音，差分輸入，I²C，靜音，短路和熱保護，關機，音量控制
安裝類型： 表面貼裝
供應商設備封裝： 36-WLP
封裝/外殼： 36-UFBGA，WLCSP
包裝： 帶卷 (TR)
配用： MAX9776EVKIT+-ND - EVALUATION KIT FOR MAX9776
Click-and-Pop Suppression
In conventional single-supply headphone amplifiers, the
output-coupling capacitor is a major contributor of audi-
ble clicks and pops. Upon startup, the amplifier charges
the coupling capacitor to its bias voltage, typically half the
supply. Likewise, during shutdown, the capacitor is dis-
charged to GND. This results in a DC shift across the
capacitor, which, in turn, appears as an audible transient
at the speaker. Since the MAX9775/MAX9776 headphone
amplifier does not require output-coupling capacitors, this
problem does not arise.
In most applications, the output of the preamplifier dri-
ving the MAX9775/MAX9776 has a DC bias of typically
half the supply. During startup, the input-coupling
capacitor is charged to the preamplifier’s DC bias volt-
age, resulting in a DC shift across the capacitor and an
audible click/pop. An internal delay of 30ms eliminates
the click/pop caused by the input filter.
Shutdown
The MAX9775/MAX9776 feature a 0.1A hard shutdown
mode that reduces power consumption to extend battery
life and a soft shutdown where current consumption is
typically 8.5A. Hard shutdown is controlled by connect-
ing the SHDN pin to GND, disabling the amplifiers, bias
circuitry, charge pump, and I2C. In shutdown, the head-
phone amplifier output impedance is 1.4k
Ω and the
speaker output impedance is 300k
Ω. Similarly, the
MAX9775/MAX9776 enter soft-shutdown when the SHDN
bit = 0 (see Table 2). The I2C interface is active and the
contents of the command register are not affected when
in soft-shutdown. This allows the master to write to the
MAX9775/MAX9776 while in shutdown. The I2C interface
is completely disabled in hardware shutdown. When the
MAX9775/MAX9776 are re-enabled the default settings
are applied (see Table 3).
I2C Interface
The MAX9775/MAX9776 feature an I2C 2-wire serial
interface consisting of a serial data line (SDA) and a
serial clock line (SCL). SDA and SCL facilitate commu-
nication between the MAX9775/MAX9776 and the mas-
ter at clock rates up to 400kHz. Figure 8 shows the
2-wire interface timing diagram. The MAX9775/
MAX9776 are receive-only slave devices relying on the
master to generate the SCL signal. The master, typical-
ly a microcontroller, generates SCL and initiates data
transfer on the bus. The MAX9775/MAX9776 cannot
write to the SDA bus except to acknowledge the receipt
of data from the master. The MAX9775/MAX9776 will
not acknowledge a read command from the master.
A master device communicates to the MAX9775/
MAX9776 by transmitting the proper address followed
by the data word. Each transmit sequence is framed by
a START (S) or REPEATED START (Sr) condition and a
STOP (P) condition. Each word transmitted over the
bus is 8 bits long and is always followed by an
acknowledge clock pulse.
The MAX9775/MAX9776 SDA line operates as both an
input and an open-drain output. A pullup resistor,
greater than 500
Ω, is required on the SDA bus. The
MAX9775/MAX9776 SCL line operates as an input only.
A pullup resistor (greater than 500
Ω) is required on
SCL if there are multiple masters on the bus or if the
master in a single-master system has an open-drain
SCL output. Series resistors in line with SDA and SCL
are optional. Series resistors protect the digital inputs of
the MAX9775/MAX9776 from high-voltage spikes on
the bus lines, and minimize crosstalk and undershoot of
the bus signals.
MAX9775/MAX9776
2 x 1.5W, Stereo Class D Audio Subsystem
with DirectDrive Headphone Amplifier
______________________________________________________________________________________
25
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START
CONDITION
START
CONDITION
tHD, STA
tSU, STA
tHD, STA
tSP
tBUF
tSU, STO
tLOW
tSU, DAT
tHD, DAT
tHIGH
tR
tF
Figure 8. 2-Wire Serial-Interface Timing Diagram
相關PDF資料
PDF描述
MS27508E18B11S CONN RCPT 11POS BOX MNT W/SCKT
MS3106F16-10P CONN PLUG 3POS STRAIGHT W/PINS
MAX13330GEE/V+T IC AMP STEREO HEADPHONE 16-QSOP
LTC2480HDD#TRPBF IC ADC DELTA SIGMA 16BIT 10DFN
MAX9789BETJ+T IC AMP AUDIO 2W STER AB 32TQFN
相關代理商/技術參數
參數描述
MAX9776ETJ+ 功能描述:音頻放大器 2 x 1.5W Stereo Class D Subsystem RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9776ETJ+T 功能描述:音頻放大器 2 x 1.5W Stereo Class D Subsystem RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9776EVKIT+ 功能描述:音頻 IC 開發工具 MAX9776 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
MAX9777ETI+ 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
MAX9777ETI+T 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*