- 您現在的位置：買賣IC網 > PDF目錄1945 > MAX7360EWX+T (Maxim Integrated Products)IC CTRLR KEY-SWITCH I2C 36-WLP PDF資料下載
參數資料
| 型號： | MAX7360EWX+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/32頁 |
| 文件大小： | 0K |
| 描述： | IC CTRLR KEY-SWITCH I2C 36-WLP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 控制器 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | I²C，2 線串口 |
| 電流 - 電源： | 50µA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-WFBGA，WLCSP |
| 供應商設備封裝： | 36-WLP（2.57x2.57） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
17
Maxim Integrated
I2C-Interfaced Key-Switch Controller and LED
Driver/GPIOs with Integrated ESD Protection
MAX7360
Figure 10. Ghost-Key Phenomenon
Figure 11. Valid Three-Key Combinations
Ghost-Key Elimination
Ghost keys are a phenomenon inherent with key-switch
matrices. When three switches located at the corners
of a matrix rectangle are pressed simultaneously, the
switch that is located at the last corner of the rectangle
(the ghost key) also appears to be pressed. This occurs
because the potentials at the two sides of the ghost-key
switch are identical due to the other three connections—
the switch is electrically shorted by the combination of
the other three switches (Figure 10). Because the key
appears to be pressed electrically, it is impossible to
detect which of the four keys is the ghost key.
The MAX7360 employs a proprietary scheme that detects
any three-key combination that generates a fourth ghost
key, and does not report the third key that causes a
ghost-key event. This means that although ghost keys
are never reported, many combinations of three keys
are effectively ignored when pressed at the same time.
Applications requiring three-key combinations (such
as <Ctrl><Alt><Del>) must ensure that the three keys
are not wired in positions that define the vertices of a
rectangle (Figure 11). There is no limit on the number of
keys that can be pressed simultaneously as long as the
keys do not generate ghost-key events and FIFO is not full.
Low-EMI Operation
The MAX7360 uses two techniques to minimize EMI
radiating from the key-switch wiring. First, the voltage
across the switch matrix never exceeds +0.55V if not
in sleep mode, independent of supply voltage VCC.
This reduces the voltage swing at any node when a
switch is pressed to +0.55V maximum. Second, the keys
are not dynamically scanned, which would cause the
key-switch wiring to continuously radiate interference.
Instead, the keys are monitored for current draw (only
occurs when pressed), and debounce circuitry only
operates when one or more keys are actually pressed.
Switch On-Resistance
The MAX7360 is designed to be insensitive to resistance,
either in the key switches, or the switch routing to and
from the appropriate COL_ and ROW_ up to 4kI (max).
These controllers are therefore compatible with low-cost
membrane and conductive carbon switches.
Hot Insertion
The INTI, INTK, SCL, and AD0 inputs and SDA remain
high impedance with up to +3.6V asserted on them
when the MAX7360 powers down (VCC = 0). I/O ports
(PORT0–PORT7) remain high impedance with up to
+14V asserted on them when not powered. Use the
MAX7360 in hot-swap applications.
Staggered PWM
The LED’s on-time in each PWM cycle are phase
delayed 45N into eight evenly spaced start positions.
Optimize phasing when using fewer than eight ports as
constant-current outputs by allocating the ports with the
most appropriate start positions. For example, if using
four constant-current outputs, choose PORT0, PORT2,
PORT4, and PORT6 because their PWM start positions
are evenly spaced. In general, choose the ports that
spread the PWM start positions as evenly as possible.
This optimally spreads out the current demand from the
ports’ load supply.
INTK/INTI
There are two interrupt outputs, INTK and INTI. Each
interrupt operates independently from the other. See
the Key-Switch Interrupt Register (0x03) and the GPIO
Port Interrupts (INTI) sections for additional information
regarding these two interrupts.
Power-Supply Considerations
The MAX7360 operates with a +1.62V to +3.6V power-
supply voltage. Bypass the power supply to GND with a
0.1FF or higher ceramic capacitor as close as possible
to the device.
REGULAR KEYPRESS
EVENT
GHOST-KEY
EVENT
KEY-SWITCH MATRIX
EXAMPLES OF VALID THREE-KEY COMBINATIONS
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7368EUE+T | IC MULTIPLEXER DUAL 4X1 16TSSOP |
| MAX7457ETE+ | IC SW VIDEO DL SCART 16TQFN |
| MAX9112ESA+T | IC DRVR DUAL LVDS 8-SOIC |
| MAX9113ESA+ | IC LINE RCVR LVDS DUAL 8SOIC |
| MAX9122EUE+T | IC LINE RCVR LVDS QUAD 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7365EWA70+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX7365EWA70+T | 制造商:Maxim Integrated Products 功能描述:KEYBOARD CONTROLLER PLUS 5 ADDITIONAL GPIOS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTRLR KEY-SWITCH I2C 25WLP |
| MAX7366ACWJ+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX7366ACWJ+T | 功能描述:視頻 IC 3D VIDEO COMBINER/ SYNCHRONIZER RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MAX7366ASWJ+ | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發(fā)布緊急采購，3分鐘左右您將得到回復。