參數資料
型號： MAX7360ETL+T
廠商： Maxim Integrated Products
文件頁數： 9/32頁
文件大?。?/td> 0K
描述： IC CTRLR KEY-SW I2C 40TQFN-EP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
類型： 控制器
輸入類型： 邏輯
輸出類型： 邏輯
接口： I²C，2 線串口
電流 - 電源： 50µA
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-TQFN-EP（5x5）
包裝： 帶卷 (TR)
17
Maxim Integrated
I2C-Interfaced Key-Switch Controller and LED
Driver/GPIOs with Integrated ESD Protection
MAX7360
Figure 10. Ghost-Key Phenomenon
Figure 11. Valid Three-Key Combinations
Ghost-Key Elimination
Ghost keys are a phenomenon inherent with key-switch
matrices. When three switches located at the corners
of a matrix rectangle are pressed simultaneously, the
switch that is located at the last corner of the rectangle
(the ghost key) also appears to be pressed. This occurs
because the potentials at the two sides of the ghost-key
switch are identical due to the other three connections—
the switch is electrically shorted by the combination of
the other three switches (Figure 10). Because the key
appears to be pressed electrically, it is impossible to
detect which of the four keys is the ghost key.
The MAX7360 employs a proprietary scheme that detects
any three-key combination that generates a fourth ghost
key, and does not report the third key that causes a
ghost-key event. This means that although ghost keys
are never reported, many combinations of three keys
are effectively ignored when pressed at the same time.
Applications requiring three-key combinations (such
as <Ctrl><Alt><Del>) must ensure that the three keys
are not wired in positions that define the vertices of a
rectangle (Figure 11). There is no limit on the number of
keys that can be pressed simultaneously as long as the
keys do not generate ghost-key events and FIFO is not full.
Low-EMI Operation
The MAX7360 uses two techniques to minimize EMI
radiating from the key-switch wiring. First, the voltage
across the switch matrix never exceeds +0.55V if not
in sleep mode, independent of supply voltage VCC.
This reduces the voltage swing at any node when a
switch is pressed to +0.55V maximum. Second, the keys
are not dynamically scanned, which would cause the
key-switch wiring to continuously radiate interference.
Instead, the keys are monitored for current draw (only
occurs when pressed), and debounce circuitry only
operates when one or more keys are actually pressed.
Switch On-Resistance
The MAX7360 is designed to be insensitive to resistance,
either in the key switches, or the switch routing to and
from the appropriate COL_ and ROW_ up to 4kI (max).
These controllers are therefore compatible with low-cost
membrane and conductive carbon switches.
Hot Insertion
The INTI, INTK, SCL, and AD0 inputs and SDA remain
high impedance with up to +3.6V asserted on them
when the MAX7360 powers down (VCC = 0). I/O ports
(PORT0–PORT7) remain high impedance with up to
+14V asserted on them when not powered. Use the
MAX7360 in hot-swap applications.
Staggered PWM
The LED’s on-time in each PWM cycle are phase
delayed 45N into eight evenly spaced start positions.
Optimize phasing when using fewer than eight ports as
constant-current outputs by allocating the ports with the
most appropriate start positions. For example, if using
four constant-current outputs, choose PORT0, PORT2,
PORT4, and PORT6 because their PWM start positions
are evenly spaced. In general, choose the ports that
spread the PWM start positions as evenly as possible.
This optimally spreads out the current demand from the
ports’ load supply.
INTK/INTI
There are two interrupt outputs, INTK and INTI. Each
interrupt operates independently from the other. See
the Key-Switch Interrupt Register (0x03) and the GPIO
Port Interrupts (INTI) sections for additional information
regarding these two interrupts.
Power-Supply Considerations
The MAX7360 operates with a +1.62V to +3.6V power-
supply voltage. Bypass the power supply to GND with a
0.1FF or higher ceramic capacitor as close as possible
to the device.
REGULAR KEYPRESS
EVENT
GHOST-KEY
EVENT
KEY-SWITCH MATRIX
EXAMPLES OF VALID THREE-KEY COMBINATIONS
相關PDF資料
PDF描述
MXB7846EEE+T IC CNTRLR TOUCH RES 16QSOP
V24C28M100BG CONVERTER MOD DC/DC 28V 100W
PCF51JM128VLH MCU 32BIT 128K FLASH 64-LQFP
V24C28M100B CONVERTER MOD DC/DC 28V 100W
MC9S08LC36LH IC MCU 36K FLASH 2K RAM 64-LQFP
相關代理商/技術參數
參數描述
MAX7360EVKIT+ 制造商:Maxim Integrated Products 功能描述:I2C-INTERFACED KEY-SWITCH CONTROLLE - Boxed Product (Development Kits)
MAX7360EWX+ 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C-Interfaced Key-Switch Controller and LED Driver/GPIOs with Integrated ESD Protection
MAX7360EWX+T 功能描述:外圍驅動器與原件 - PCI Key-Switch Ctlr & LED Driver/GPIO RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
MAX7365EWA70+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX7365EWA70+T 制造商:Maxim Integrated Products 功能描述:KEYBOARD CONTROLLER PLUS 5 ADDITIONAL GPIOS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTRLR KEY-SWITCH I2C 25WLP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*