參數資料
型號: MAX7360ETL+T
廠商: Maxim Integrated Products
文件頁數: 5/32頁
文件大?。?/td> 0K
描述: IC CTRLR KEY-SW I2C 40TQFN-EP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
類型: 控制器
輸入類型: 邏輯
輸出類型: 邏輯
接口: I²C,2 線串口
電流 - 電源: 50µA
安裝類型: 表面貼裝
封裝/外殼: 40-WFQFN 裸露焊盤
供應商設備封裝: 40-TQFN-EP(5x5)
包裝: 帶卷 (TR)
13
Maxim Integrated
I2C-Interfaced Key-Switch Controller and LED
Driver/GPIOs with Integrated ESD Protection
MAX7360
in automatically cancels that port’s fade and immedi-
ately output at its newly programmed intensity.
4) Put the part into shutdown to cause all ports to fade
out. Changing an individual PWM intensity during
fade out automatically cancels that port’s fade and
immediately turns off.
Blink
Each port has its own blink control settings through reg-
isters 0x58 to 0x5F (see Table 25 in the Register Tables
section). The blink period ranges from 0 (blink disabled)
to 4.096s. Settable blink duty cycles range from 6.25%
to 50%. All blink periods start at the same PWM cycle for
synchronized blinking between multiple ports.
GPIO Port Interrupts (INTI)
Three possible sources generate INTI: I2C timeout,
GPIOs configured as inputs, and the rotary switch
(registers 0x48, 0x49, and 0x4A). Read the respective
data/status registers for each type of interrupt to clear
INTI. Set register 0x46 for rotary switch-based interrupts.
Set registers 0x58 to 0x5F for individual GPI-based inter-
rupts. If multiple sources generate the interrupt, all the
related status registers must be read to clear INTI.
Rotary Switch
The MAX7360 can accept a 2-bit rotary switch inputs on
PORT6 and PORT7. Rotation of the switch in a clockwise
direction increments the count. Enable rotary switch
mode from the GPIO global configuration register (0x40).
Several settings for PORT6 and PORT7 occur during
rotary switch mode:
1) Each port has a 10FA pullup to VCC.
2) Register 0x46 sets the debounce time.
3) A debounced rising edge on PORT6 while PORT7 is
high decreases the count.
4) A debounced rising edge on PORT6 while PORT7 is
low increases the count.
For more details, see Figure 1.
Serial Interface
Figure 2 shows the 2-wire serial interface timing details.
Serial Addressing
The MAX7360 operates as a slave that sends and
receives data through an I2C-compatible 2-wire inter-
face. The interface uses a serial-data line (SDA) and
a serial-clock line (SCL) to achieve bidirectional com-
munication between master(s) and slave(s). A master
(typically a microcontroller) initiates all data transfers to
and from the MAX7360 and generates the SCL clock that
synchronizes the data transfer.
The MAX7360’s SDA line operates as both an input and
an open-drain output. A pullup resistor, typically 4.7kI,
Figure 2. 2-Wire Serial Interface Timing Details
Figure 1. Rotary Switch Input Signal Timing
SDA
SCL
tHD, STA
tLOW
tHIGH
tR
tF
tSU, DAT
tSU, STA
tSU, STO
tBUF
tHD, STA
tHD, DAT
START
CONDITION
STOP
CONDITION
START
CONDITION
REPEATED
START CONDITION
tF
tF, TX
tR
PORT7
PORT6
PORT7
PORT6
INCREMENT
DECREMENT
ROTARY SWITCH
DEBOUNCE
相關PDF資料
PDF描述
MXB7846EEE+T IC CNTRLR TOUCH RES 16QSOP
V24C28M100BG CONVERTER MOD DC/DC 28V 100W
PCF51JM128VLH MCU 32BIT 128K FLASH 64-LQFP
V24C28M100B CONVERTER MOD DC/DC 28V 100W
MC9S08LC36LH IC MCU 36K FLASH 2K RAM 64-LQFP
相關代理商/技術參數
參數描述
MAX7360EVKIT+ 制造商:Maxim Integrated Products 功能描述:I2C-INTERFACED KEY-SWITCH CONTROLLE - Boxed Product (Development Kits)
MAX7360EWX+ 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C-Interfaced Key-Switch Controller and LED Driver/GPIOs with Integrated ESD Protection
MAX7360EWX+T 功能描述:外圍驅動器與原件 - PCI Key-Switch Ctlr & LED Driver/GPIO RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
MAX7365EWA70+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX7365EWA70+T 制造商:Maxim Integrated Products 功能描述:KEYBOARD CONTROLLER PLUS 5 ADDITIONAL GPIOS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTRLR KEY-SWITCH I2C 25WLP